RAM Mounts držiak s dvojitým otočným ramenom

RAM Mounts držiak VESA 75x75 mm, s 1,5" guľovým čapom, RAM-2461U EAN: 793442024610 Prehľad Držiak VESA 75x75 mm s 1,5" guľovým čapom. Štvorcová doštička držiaka s rozmermi 92x92 mm. Čap umiestnený 22 mm od stredu hrany. Použitie VESA 75x75 držiak pre LCD monitory, priemyselné PC, terminály atď. Úchyt na rovnú plochu so širokou podstavou pre rad "C" ramien a držiakov RAM s 1,5" čapy. Prednosti Kompatibilný so systémom ramien a úchytov RAM mount radu "C". Zodpovedá štandardu VESA 75x75. Dokonalé spracovanie. Doživotná záruka RAM mount. Špecifikácia Materiál: Povlakovaná zliatina hliníka Váha: 182 g Veľkosť guľového čapu: 1,5", gumový, veľkosti "C" Poznámka: "U" v čísle dielu znamená, že výrobok je balený v PU sáčku.

Objav podobné ako RAM Mounts držiak VESA 75x75 mm, s 1,5" guľovým čapom, RAM-2461U

Tento RAM Mounts GDS Tough-Dock držiak s kľúčovým zámkom je určený pre Samsung Tab A9+ v IntelliSkin Next Gen ochrannom obale. Držiak nabíja tablet cez USB-C konektor a poskytuje USB-A port pre pripojenie periférií. Spodná časť držiaka je prispôsobená na pripevnenie na guľovú základňu.

• Bezpečné pripevnenie tabletu pomocou kľúčového zámku
• Nabíjanie tabletu cez USB-C konektor s výkonom 15W
• Podpora periférnych zariadení cez USB-A port
• Jednoduchá inštalácia a vyberanie tabletu

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

RAM Mounts GDS Uni-Conn je pružinová dokovacia stanica navrhnutá pre zariadenia v IntelliSkin prípadoch s Uni-Conn adaptérom. Zabezpečuje bezpečné uchytenie a rýchle nabíjanie cez pogo piny s USB-C pripojením. Obsahuje aj USB-A port pre periférne zariadenia.

• Univerzálna dokovacia stanica s pružinovým mechanizmom pre rýchle a bezpečné uchytenie.
• Podpora rýchleho nabíjania cez integrované pogo piny s USB-C vstupom a výkonom 15W.
• Dodatočný USB-A port pre pripojenie periférneho zariadenia (napr. myš alebo klávesnica).
• Jednoduchá inštalácia a kompatibilita s IntelliSkin prípadmi a Uni-Conn adaptérom.

Objav podobné ako RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Screw-Set

RAM Mounts nabíjacia stanica pre Honeywell CT40
dokovacia stanica RAM Mounts Form-Fit pre Getac ZX10
RAM Mounts dokovacia stanica s VESA uchytením
univerzálna nabíjacia dokovacia stanica RAM Mounts
RAM Mounts nabíjacia stanica pre Honeywell RT10
upevnenie RAM Mounts pre Honeywell RT10
batéria s otočným ramenom pre drez
batéria s otočným ramenom 28,1 cm
drezová batéria s otočným ramenom
stojanová batéria do kuchyne s otočným ramenom
kvalitná batéria s otočným ramenom
moderný držiak na uteráky s dvojitým úchytom
pohodlný držiak na uteráky s otočným mechanizmom
RAM-GDS-DOCKL-SAM88CDU držiak s USB-C a USB-A konektorom
držiak zariadení do vozidla RAM
umývadlová batéria s ramenom 9 cm

RAM Mounts Universal Vehicle Mount je univerzálny držiak určený pre montáž do vozidiel. Skladá sa z vozidlovej základne, dvojitého otočného ramena a využíva štandardné AMPS pripojenie. Umožňuje bezpečné a prispôsobiteľné umiestnenie rôznych elektronických zariadení počas jazdy.

• Univerzálna kompatibilita s rôznymi zariadeniami
• Dvojité otočné rameno pre maximálnu prispôsobiteľnosť
• Odolná konštrukcia z kvalitných materiálov
• Jednoduchá inštalácia a nastavenie

Objav podobné ako RAM Mounts Universal Vehicle Mount

Dokovacia stanica RAM Mounts Form-Fit je navrhnutá špecificky pre tablet Getac ZX10. Poskytuje napájanie a dátové pripojenie cez duálne USB-A porty. Ponúka flexibilné montážne možnosti vďaka kompatibilite s AMPS a VESA štandardmi.

• Poskytuje spoľahlivé napájanie a dátové pripojenie cez duálne USB-A porty
• Univerzálne uchytenie kompatibilné s 4-dierovým AMPS a VESA štandardom
• Špeciálne navrhnutá pre dokonalé prispôsobenie tabletu Getac ZX10
• Robustná konštrukcia vhodná pre profesionálne a náročné prostredia

Objav podobné ako RAM Mounts Form-Fit Docking Station

RAM Mounts Charging Dock je nabíjacia stanica navrhnutá pre tablety Honeywell RT10. Ponúka dvojité USB-A výstupy a 5.5 mm jack vstup na napájanie. Je kompatibilná s VESA 75x75 upevnením pre flexibilnú inštaláciu.

• Dvojité USB-A porty pre súčasné nabíjanie viacerých zariadení
• Kompatibilita s VESA 75x75 štandardom pre jednoduchú inštaláciu
• Špecificky navrhnutá pre robustné tablety Honeywell RT10
• 5.5 mm jack vstup pre spoľahlivé napájanie

Objav podobné ako RAM Mounts Charging Dock

RAM Mounts nabíjacia stanica je určená pre ručné terminály Honeywell CT40, CT45 a CT47. Ponúka uzamykateľnú konštrukciu, vstup 5.5 mm jack a USB-A výstup. Upevňuje sa pomocou štandardného 2-otvorového AMPS systému.

• Uzamykateľná konštrukcia pre bezpečné nabíjanie
• Univerzálna kompatibilita s radom Honeywell CT40/45/47
• Jednoduchá inštalácia pomocou 2-otvorového AMPS upevnenia
• Praktický USB-A výstup pre flexibilné napájanie

Objav podobné ako RAM Mounts Charging Station

Páková umývadlová batéria Hansa Vantis Style s otočným ramienkom je vyrobená z brúsenej ocele s matným povrchom. Dosahuje prietok 10,2 litra za minútu a má výšku 33 cm s ramenom dlhým 28,1 cm. Je určená pre inštaláciu na drezy.

• Otočné ramienko pre pohodlné používanie
• Matný povrch v brúsenom ocelovom prevedení
• Vysoký prietok vody 10,2 l/min
• Kompaktné rozmery vhodné pre umývadlá

Objav podobné ako Hansa Vantis Style drezová batéria s otočným ramienkom brúsená oceľ 5420220780

Grohe Essence New je vysoká stojančeková umývadlová batéria s otočným ramienkom. Je vyrobená v supersteel farebnom prevedení, ktoré je odolné a ľahko sa udržiava. Batéria je vhodná pre kuchynské umývadlá a ponúka pohodlné používanie vďaka vysokej konštrukcii.

• Vysoký výlevok umožňuje pohodlné umývanie väčších predmetov
• Otočné ramienko poskytuje flexibilitu pri používaní
• Supersteel povrch je odolný proti škrabancom a ľahko sa čistí
• Pákový ovládač umožňuje jednoduché a presné nastavenie teploty a prietoku vody

Objav podobné ako Grohe Essence New vysoká umývadlová batéria s otočným ramienkom supersteel 32628dc1 G32628DC1

RAM Mounts X-Grip univerzálny držiak na mobilný telefón EAN: 793442932298 Popis produktu RAM Mounts X-Grip je univerzálny držiak na mobilný telefón s 1" guľovým čapom. Skladá sa z pružinového mechanizmu, ktorý bezpečne udrží váš telefón. Držiak je doplnený zaisťovacou gumou pre maximálne bezpečie vášho zariadenia. Špecifikácia Šírka telefónu: 48 – 83 mm Hrúbka telefónu: do 22 mm Materiál: Nerez oceľ, povlakovaná zliatina hliníka, vysokopevnostný plast Váha: 100 g Veľkosť guľového čapu: 1", gumový, veľkosti „B“ Výhody produktu Držiak X-Grip ponúka bezpečné uchopenie telefónu aj pri vibráciách. Je univerzálny a kompatibilný so systémom ramien a úchytov RAM mount. Ponúka rýchle a jednoduché upevnenie aj vybratie telefónu. Je nehrdzavejúci a dodáva sa s doživotnou zárukou RAM mount. Upozornenie: X-Grip je súčasťou trojdielneho riešenia. Na zostavenie celého riešenia potrebujete okrem tohto držiaka ešte rameno a úchyt.

Objav podobné ako RAM Mounts X-Grip univerzálny držiak na mobilný telefón s 1" guľovým čapom

RAM Mounts X-Grip Univerzálny Držiak pre Veľké Telefóny EAN: 793442940873 Popis produktu Univerzálny držiak X-Grip je navrhnutý pre bezpečné uchytenie mobilných telefónov a smartfónov s veľkosťou väčšou ako 5". Bezpečnosť a pohodlie Držiak je vybavený pružinovým mechanizmom a gumovou podložkou, ktoré zaisťujú bezpečnosť a pohodlie vášho telefónu. Zaisťovacia guma Súčasťou balenia je zaisťovacia guma, ktorá zabraňuje vypadnutiu telefónu aj v extrémnych podmienkach. Rozsah držiaka Šírka telefónu: 44 - 114 mm Hrúbka telefónu: do 22 mm Overte si, že rozmery vášho telefónu sú menšie ako rozsah držiaka. Materiál Držiak je vyrobený z nerez ocele, povlakovanej zliatiny hliníka a vysokopevnostného plastu. Veľkosť guľového čapu Guľový čap má priemer 1" a je kompatibilný so všetkými "B" veľkosťami RAM mount ramien. Váha Držiak váži 114 g. Prednosti držiaka XGrip Bezpečne drží telefón aj pri vibráciách Univerzálna pre telefóny v puzdre aj bez Rýchle a jednoduché upevnenie a vybratie telefónu Kompatibilný so systémom ramien a úchytov RAM mount Nehrdzavejúci Doživotná záruka RAM mount Upozornenie X-Grip je časť trojdielneho riešenia. Okrem tohto držiaka potrebujete ešte rameno a úchyt na zostavenie celého riešenia.

Objav podobné ako RAM Mounts X-Grip univerzálny držiak na veľké telefóny s 1" guľovým čapom, RAM-HOL-UN10BU

Nastaviteľný TV držiak na stenu je optimálne riešenie pre miesta s horšími svetelnými podmienkami alebo pre domácnosti a priestory, kde je sedenie rozmiestnené na viacerých miestach. Aby ste vedeli flexibilne zareagovať na Vaše potreby, môžete natočiť držiak v rozsahu 180° a nakloniť v rozsahu 30°. Zároveň je možné otočiť ho o 360°. Otočný TV držiak je vhodný pre zariadenia s otvormi 100 x 100, 100 x 200 a 200 x 200 mm, preto naňho môžete upevniť rôzne televízory.Minimálna vzdialenosť držiaka od steny je 9,7 cm. Táto vzdialenosť predstavuje dostatočnú flexibilitu a umožní Vám jednoduchý prístup ku všetkým portom a zároveň držiak nezaberie príliš veľa miesta.Všetok potrebný montážny materiál je súčasťou balenia TV držiaka na stenu. Vezmite prosím na vedomie, že fotografie zobrazujú totožný čierny model.

Objav podobné ako Electronic-Star Electronic star, nastaviteľný TV nástenný držiak s otočným ramenom, <15 kg

Nastaviteľný TV držiak na stenu je optimálne riešenie pre miesta s horšími svetelnými podmienkami alebo pre domácnosti a priestory, kde je sedenie rozmiestnené na viacerých miestach. Aby ste vedeli flexibilne zareagovať na Vaše potreby, môžete natočiť držiak v rozsahu 180° a nakloniť v rozsahu 30°. Zároveň je možné otočiť ho o 360°. Otočný TV držiak je vhodný pre zariadenia s otvormi 100 x 100, 100 x 200 a 200 x 200 mm, preto naňho môžete upevniť rôzne televízory.Minimálna vzdialenosť držiaka od steny je 9,7 cm. Táto vzdialenosť predstavuje dostatočnú flexibilitu a umožní Vám jednoduchý prístup ku všetkým portom a zároveň držiak nezaberie príliš veľa miesta.Všetok potrebný montážny materiál je súčasťou balenia TV držiaka na stenu. Vezmite prosím na vedomie, že fotografie zobrazujú totožný čierny model.

Objav podobné ako Electronic-Star Electronic star, nastaviteľný TV nástenný držiak s otočným ramenom, <15 kg

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Potrebujete na motorku pripevniť svoj telefón? Hodiť sa vám tak rozhodne bude držiak na mobil RAM Mounts. Stojan na mobil je pripravený na mechanické upevnenie telefónu. Dáte do neho telefón so šírkou od 4,8 do 8,3 cm. Držiak mobilu na motorku vám dobre poslúži na cestách. Hlavné prednosti držiaka na mobil RAM Mounts kompletná zostava univerzálneho držiaka X-Grip na riadidlá do priemeru 60 mm Vďaka držiaku na mobil RAM Mounts budete mať telefón stále na očiach Je určený pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón nasadíte na držiak ručne Držiak telefónu RAM Mounts je pripravený na motorku

Objav podobné ako RAM Mounts kompletná zostava univerzálneho držiaka X-Grip na riadidlá do priemeru 60 mm (M021-007)

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Potrebujete na motorku pripevniť telefón? Vhodným riešením pre vás môže byť držiak na mobil RAM Mounts. Stojan na mobil je z výroby pripravený na mechanické upevnenie telefónu. Vložíte do neho telefón so šírkou od 4,8 až do 8,3 cm. Držiak mobilu na motorku vám spríjemní cestovanie. Hlavné vlastnosti držiaka na mobil RAM Mounts kompletná zostava držiaku X-Grip s uchytením do krku riadenia motocykla Vďaka držiaku na mobil RAM Mounts budete mať telefón stále poruke Je určený pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón umiestnite do držiaka ručne Držiak telefónu RAM Mounts je pripravený na motorku

Objav podobné ako RAM Mounts kompletná zostava držiaku X-Grip s uchytením do krku riadenia motocykla (M021-073)

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Chcete na motorku pripevniť telefón? Osloviť vás môže držiak na mobil RAM Mounts. Stojan na mobil má z výroby nachystané mechanické upevnenie telefónu. Prichytíte do neho telefón so šírkou od 4,8 až do 8,3 cm. Držiak mobilu na motorku oceníte pri cestovaní. Zásadné vlastnosti držiaka na mobil RAM Mounts kompletná zastava držiaku mobilného telefonu „X-Grip" s uchytením na 9 mm skurtku Pomocou držiaka na mobil RAM Mounts budete mať telefón stále poruke Hodí sa pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón prichytíte k držiaku mechanicky Držiak telefónu RAM Mounts je nachystaný na motorku

Objav podobné ako RAM Mounts kompletná zastava držiaku mobilného telefonu „X-Grip s uchytením na 9 mm skurtku (M021-058)

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PD2U:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp- Right or NFC-RepeaterInput Connector: 5.5mm DCOutput ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PDLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCOutput ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Zebra ET80/85

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22LU:Compatible with accessoriesEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22LU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU:Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25LU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable & DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A/DB-Sub-Anschluss

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A Connector

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & USB-A Connector

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5KLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with Keys Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PD2KLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: 2x ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC & Dual USB-A Connector

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PD2U: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal With Latch Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: 2x USB-A ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX80 Rugged Tablet - 5.5mm DC & Dual USB-A Connector

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PDKLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: USB-A 2.0 ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC & USB-A Connector

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PDU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal With Latch Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: USB-A 2.0 (Peripheral ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX80 Rugged Tablet - 5.5mm DC & USB-A Connector

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PKLU: Compatible with the Getac tablet accessoires Not compatible with the Getac 4-point hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Buchse Input Voltage: 19V Output Voltage: 14V Input Cable Length: ca. 100 cm Certifications: FCC, IC, CE, UKCA, WEEE & RoHS Additional information: This holder is compatible with the Getac 2-point ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable & DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A/DB-Sub Connector

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A Connector

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & USB-A Connector

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11U: Compatible with OEM hand strap Easy insertion and removal With Latch Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Certifications: RoHS, WEEE, CE & FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot