cipherlab protective rubber boot

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

372.170013 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

252.860001 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

256.910004 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

227.720001 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

331.309998 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

300.049988 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

269.01001 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

204.600006 €

Detail kúpiť

RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11U: Compatible with OEM hand strap Easy insertion and removal With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot

154.779999 €

Detail kúpiť

Zebra Protective Boot

Protective Boot, fits for: TC501

Objav podobné ako Zebra Protective Boot

67.639999 €

Detail kúpiť

Snehule Moon Boot MB ICON LOW RUBBER

Snehule z kolekcie Moon Boot. Model vytvorený spojením textilu a ekologickej kože. Model s vystuženým zvrškom poskytuje chodidlu stabilitu.

Objav podobné ako Snehule Moon Boot MB ICON LOW RUBBER

239.899994 €

Detail kúpiť

HPE NS204i Gen11 NVM Hot Plug Boot Optimized Storage Device (2x480GB M.2 NVM SSDs HWraid1)

HPE NS204i Gen11 NVMe Hot Plug Boot Optimized Storage Device HPE NS204i OS Boot Devices obsahuje v rôznych formách továrenských zariadení a poskytuje hardvér RAID 1 riešenie pre to, že sa chystá oddeliť svoje údaje plány z ich OS plánov. NS204i môže certifikovať requirements VMware a Microsoft Storage Spaces Direct. Referencie included servera kompatibility matrix pre každú z rôznych foriem faktorov. Server platformy support a single OS Boot Device NS204i. Táto RAID optimalizovaná SSD flash sa vyrieši pomocou systému Windows, Linux, alebo VMware NVMe inbox drivers pre easy set up and reliability. The NS204i OS Boot Device nie je spotrebovaná any drive bay, takže tvoria všetky bays available for data storage. The HPE NS204i-is je univerzálna inštalácia hot plug OS Boot Device, ktorá zahŕňa dve 480GB M.2 NVMe SSDs. Táto device no longer takes up a PCIe slot, a auto-creates RAID1 volume. HPE NS204i-p a NS204i-d (SY480 Gen10 Plus) OS Boot Devices zahŕňa dve 480GB M.2 NVMe SSDs. Two 22110 M.2 NVMe SSDs musí byť pridaný do riser NS204i-r a NS204i-t Boot Controller. The NS204i boot device enables customers to zrejmé ich OS cez dedicated RAID 1. HPE NS204i je jediným directly connected NVMe drive, not a RAID controller. Ako NS204i je hardvér OS boot device, iba režim RAID 1 je podporovaný a nie je prevádzkovaný v ktoromkoľvek inom režime RAID. HPE NS204i je "plug-and-play" s nie je potrebná na configure alebo manage the device. Always ensure you running the latest iLO version and update server BIOS, FW and drivers when they become available. Poznámka: V niektorých dokumentoch a GUIs, NS204i môže byť referred to ako controller alebo device. Key Features Automatic RAID 1 creation Hardvér RAID 1 with automatic drive rebuild (2) 480 GB NVMe M.2 SSDs zahŕňajú NS204i-p a NS204i-d (SY480 Gen10 Plus option) controllers (2) On-board M.2 drive bays Utilizes native OS NVMe drivers - no custom driver needed Full HPE iLO integration for Redfish, Alerts, GUI Supporty Intel Gen10 a Intel a AMD Gen10 Plus platformy (see support matrix for details) Models HPE NS204i Gen11 NVMe Hot Plug Boot Optimized Storage Device P48183-B21 HPE NS204i-p x2 Lanes NVMe PCIe3 x8 OS Boot Device P12965-B21 HPE NS204i-d Gen10 Plus NVMe PCIe3 x4 M.2 OS Boot Device P21410-B21 HPE ProLiant DL36X Gen10 Plus x16/x8 PCIe M.2 NS204i-r Riser Kit P26463-B21 HPE NS204i-t Gen10 Plus x2 Lanes NVMe PCIe 3 x8 Boot Controller P20292-B21 M.2 Drive - Required pre NS204i-r Riser HPE 480GB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD P40513-B21

Objav podobné ako HPE NS204i Gen11 NVM Hot Plug Boot Optimized Storage Device (2x480GB M.2 NVM SSDs HWraid1)

516.070007 €

Detail kúpiť

DIOR Dior Solar The Protective Creme SPF 30 ochranný krém na tvár SPF 30 50 ml

DIOR Dior Solar The Protective Creme SPF 30, 50 ml, Starostlivosť o telo pre ženy, Opaľovací krém Dior Solar The Protective Creme SPF 30 chráni pleť pred UVA aj UVB žiarením. Jeho svieža textúra sa ľahko rozotiera a okamžite vstrebáva. Po nanesení je pleť hydratovaná, krajšia, saténovo hebká a rozžiarenejšia. Pri pravidelnom používaní zvýrazňuje opálenie. Opaľovací krém Dior Solar The Protective Creme pokožku príjemne prevonia. Vďaka kompaktnej veľkosti 50ml sa zmestí do každej kabelky či tašky, takže ho môžete mať stále so sebou. Dostupný nbsp; je tiež variant s ochranným faktorom SPF 50. Pred pobytom na slnku naneste bohaté množstvo krému na pokožku. Aplikáciu pravidelne opakujte, predovšetkým po kúpaní. Opaľovací krém Dior Solar The Protective Creme SPF 30 chráni pleť pred UVA aj UVB žiarením, a zároveň ju skrášľuje: pleť je rozjasnená, hydratovaná a rovnomerne opálená.

Objav podobné ako DIOR Dior Solar The Protective Creme SPF 30 ochranný krém na tvár SPF 30 50 ml

38 €

Detail kúpiť

Institut Esthederm Adaptasun Hydra-Protective Sun Water opaľovací sprej s vysokou UV ochranou 150 ml

Institut Esthederm Adaptasun Hydra-Protective Sun Water, 150 ml, Ochrana pred slnečným žiarením na tvár pre ženy, Opaľovací krém, ktorý stimuluje a posilňuje prirodzené opálenie Objavte slnečnú starostlivosť, ktorá myslí na krásu aj zdravie pokožky aj pleti. Opaľovací sprej s vysokou UV ochranou Institut Esthederm Adaptasun Hydra-Protective Sun Water chráni pred škodlivými vplyvmi UV žiarenia a zároveň podporuje krásne, rovnomerné a dlhotrvajúce opálenie. Vďaka patentovanej technológii stimuluje prirodzený proces pigmentácie a zachováva mladistvosť pokožky aj počas opaľovania. Doprajte si aj vy hodvábny dotyk, zlatistý lesk a maximálny komfort na slnku – s ochranou, ktorá skutočne funguje. Vlastnosti: urýchľuje a zintenzívňuje prirodzené opálenie bez rizika spálenia chráni pokožku pred poškodením spomaľuje starnutie pokožky a pleti pôsobí preventívne proti podráždeniu posilňuje obranyschopnosť proti slnečnému stresu zabraňuje dehydratácii a chráni pred oxidačným stresom dodáva pokožke zdravý lesk a hodvábne jemný finiš Zloženie: Adaptasun technológia – stimuluje a optimalizuje proces pigmentácie pre rovnomerné a rýchle opálenie Global Cellular Protection – zaisťuje antioxidačnú ochranu a bráni poškodeniu buniek aj predčasnému starnutiu Cellular Water – podporuje vitalitu pokožky a pleti omega-3, -6 a -9 mastné kyseliny – chránia pokožku pred dehydratáciou betakarotén – podporuje rovnomerné a zlatisté opálenie provitamín A vitamín E Ako aplikovať: Pred použitím opaľovací sprej Institut Esthederm Adaptasun Hydra-Protective Sun Water dobre pretrepte, aby sa obe fázy spojili. Aplikujte rovnomerne na suchú alebo vlhkú pokožku tváre, tela a vlasov približne 20 minút pred opaľovaním. Pre zachovanie účinnej ochrany opakujte aplikáciu každé 2 hodiny, po kúpaní, osušení uterákom alebo fyzickej aktivite. Notino tip: Ochranu pred slnkom prináša aj spevňujúci protivráskový krém na tvár Institut Esthederm Bronz Repair Protective Anti-Wrinkle and Firming Face Care.

Objav podobné ako Institut Esthederm Adaptasun Hydra-Protective Sun Water opaľovací sprej s vysokou UV ochranou 150 ml

74 €

Detail kúpiť

GoPro Protective Housing (HERO11, HERO10 a HERO9 Black) (ADDIV-001)

Puzdro na kameru – ochranný kryt pre kamery GoPro HERO9/HERO10 Black, vysoká odolnosť, zvyšuje vodoodolnosť až do hĺbky 60 metrov, kompatibilný s kamerou HERO11 Black Púzdro GoPro Protective Housing je špeciálne stvorené pre outdoorovú kameru HERO10 a HERO9 Black. Dokonale zvýši jej odolnosť, ochráni ju pred nečistotami a zaistí jej vodeodolnosť až do hĺbky 60 metrov. Vďaka tomu budete môcť s kamerou zaznamenať aj podvodný svet vo väčšej hĺbke. Púzdro je velmi ľahké, vďaka čomu takmer nenavýši hmotnosť kamery. GoPro Protective Housing je ideálnym doplnkom na kameru HERO10 a HERO9 Black. Kľúčové vlastnosti púzdra GoPro Protective Housing na kameru HERO10 a HERO9 BlackPúzdro určené pre outdoorovú kameru HERO10 a HERO9 BlackDokonale zvýši jej odolnosť a ochráni ju pred nečistotamiZaistí kamere vodeodolnosť až do hĺbky 60 metrovGoPro Protective Housing je veľmi ľahkéFarebné vyhotovenie: čierno–priehľadnéRozmery: 8,2 × 7,8 × 4,5cmHmotnosť: 100g

Objav podobné ako GoPro Protective Housing (HERO11, HERO10 a HERO9 Black) (ADDIV-001)

64.900002 €

Detail kúpiť