ram mounts vysoko kvalitna prisavka s priemerom 70 mm s 1

RAM Mounts Prísavka s 1" čapom Priemer: 70 mm Váha: 91 g Veľkosť guľového čapu: Priemer 1", veľkosť "B", gumový Použitie a montáž Úchyt na sklo a akékoľvek rovné, hladké a neporézne plochy. Vhodný pre malú elektroniku - mobilné telefóny, GPS navigácie, iPhone, iPod, GoPro kamery atď. aj v náročnom vibrujúcom prostredí. Jednoduchá a rýchla montáž pomocou zámku. Materiál Vysokopevnostný plast a guma Upozornenie "U" v čísle dielu znamená, že výrobok je balený v PU sáčku. Ďalšie informácie Na upevnenie držiaka s prísavkou na akýkoľvek iný povrch ako sklo, napríklad na palubnú dosku, použite samolepiacu podložku.

Objav podobné ako RAM Mounts vysoko kvalitná prísavka s priemerom 70 mm s 1" čapom

Prísavka – prísavka dvojdielna Dvojdielnu prísavku s priemerom 115 mm, ktorá je vyrobená známou a overenou spoločnosti Geko, si iste veľmi rýchlo zamilujete a určite by nemala chýbať vo vašej dielni či garáži. Táto certifikovaná prísavka je skvelým riešením pri transporte okna, sklenených predmetov, laminátu či plechov. Disponuje nosnosťou až 80 kg a vyrobená je z kvalitného hliníka. Hlavné prednosti 2-dielnej hliníkovej prísavky Geko, priemer 115 mmDvojdielna prísavka vyrobená spoločnosťou GekoZhotovená z kvalitného pevného hliníkaVýborná na transport okien, skla, laminátu či plechuPrísavka je vyrobená v striebornej farbeGumové koncovky pre maximálnu priľnavosťNosnosť:80 kgPriemer:115 mm

Objav podobné ako GEKO Prísavka dvojdielna hilníková, priemer 115 mm (G02454)

Prísavka – prísavka trojdielna Trojdielnu prísavku s priemerom 115 mm, ktorá je vyrobená známou a overenou spoločnosti Geko, si iste veľmi rýchlo zamilujete a určite by nemala chýbať vo vašej dielni či garáži. Táto certifikovaná prísavka je skvelým riešením pri transporte okna, sklenených predmetov, laminátu či plechov. Disponuje nosnosťou až 80 kg a vyrobená je z kvalitného hliníka. Hlavné prednosti 3-dielnej hliníkovej prísavky Geko, priemer 115 mmTrojdielna prísavka vyrobená spoločnosťou GekoZhotovená z kvalitného pevného hliníkaVýborná na transport okien, skla, laminátu či plechuPrísavka je vyrobená v striebornej farbeGumové koncovky pre maximálnu priľnavosťNosnosť:130 kgPriemer:115 mm

Objav podobné ako GEKO Prísavka trojdielna hliníková, priemer 115 mm (G02455)

Hansgrohe sprchová hlavica s priemerom 120 mm
predĺženie rozety s priemerom 170 mm
sprchová bateria s priemerom 110 mm
sprchová sada s priemerom 125 mm
zápachová uzávierka s priemerom 32 mm
sifón pre vaničku s priemerom 90 mm
vaničkový sifón s priemerom 90 mm
sprchová hlavica s priemerom 85 mm

Kolieska s priemerom 70 mm, tvrdosť: 82A, kusov v balení: 4 Tempish Catch je sada 4 náhradných koliesok do in-line korčúľ. Sú vyrobené zo zmesi polyuretánu, ktorá vyniká svojou odolnosťou a malým valivým odporom. Kolieska disponujú priemerom 70 mm, vďaka čomu ponúkajú vysokú stabilitu a ovládateľnosť, a tvrdosť 82A. Tempish Catch sú vhodné na rekreačné korčuľovanie a predovšetkým pre začiatočníkov. Kľúčové vlastnosti koliesok Tempish Catch 70 × 24 82A Sada 4 náhradných koliesok do in-line korčúľVhodná na rekreačné korčuľovanieVyrobená zo zmesi odolného polyuretánuDisponujú malým valivým odporomKolieska Tempish Catch ponúkajú vysokú stabilitu a ovládateľnosťFarebné vyhotovenie: čierno-sivé Priemer: 70 mm Tvrdosť: 82A

Objav podobné ako Tempish Catch 70×24 82A (8595049311184)

Polysan Flexia vaničkový sifón 90 mm s čiernym krytom je určený pre sprchové vaničky. Je vyrobený z nehrdzavejúcej ocele a je kompatibilný s odtokovým otvorom s priemerom 90 mm. Poskytuje spoľahlivý odtok vody a estetický vzhľad.

• Kryt z nehrdzavejúcej ocele v čiernej farbe
• Kompatibilný so sprchovými vaničkami s priemerom odtokového otvoru 90 mm
• Jednoduchá inštalácia a údržba
• Odolný a dlhotrvajúci materiál

Objav podobné ako Polysan Flexia vaničkový sifón 90 mm krytka čierna 17781

Panvica Siemens s priemerom 353 mm má nepriľnavý povrch a je vyrobená z nerezovej ocele. Ponúka praktické využitie pri každodennej príprave jedál. Jej dizajn je moderný a funkčný.

• Veľký priemer 353 mm vhodný na prípravu viacerých porcií.
• Nepriľnavý povrch uľahčuje varenie a čistenie.
• Vyrobená z odolnej nerezovej ocele pre dlhú životnosť.
• Moderný a elegantný dizajn, ktorý sa hodí do každej kuchyne.

Objav podobné ako Panvica Siemens 353 mm s nepriľnavým povrchom, nerez HZ9FF010

Sifón Polysan Flexia je určený pre sprchové vaničky s priemerom odtokového otvoru 90 mm. Kryt je vyrobený z nehrdzavejúcej ocele a má čiernu farbu. Zabezpečuje účinný odtok vody a je odolný voči opotrebovaniu.

• Kryt z nehrdzavejúcej ocele odolnejší proti korózii
• Kompatibilný so sprchovými vaničkami s odtokovým otvorom 90 mm
• Čierny kryt poskytuje moderný a diskrétny vzhľad
• Jednoduchá inštalácia a údržba

Objav podobné ako Polysan Flexia vaničkový sifón 90 mm krytka čierna 17751

Kolieskové korčule – detské, vhodné pre rekreačných korčuliarov, priemer koliesok: 70mm, tvrdosť koliesok: 82A, ložiská: ABEC 7, systém zaväzovania: šnúrky, sezóna 2019 Kvalitné kolieskové korčule značky Tempish NERROW 4 green vo veľkosti 31 – 34 EU/188 – 214 mm budú pre vás skvelým spoločníkom na vašich jazdách. Inline korčule od renomovaného výrobcu Tempish majú kolieska s priemerom 70 mm. Menšie kolieska s priemerom pod 83 mm nedosahujú síce tak vysokú rýchlosť, avšak sú viac stabilné, preto sa odporúčajú aj pre začiatočníkov. Konštrukcia korčúľ Tempish NERROW 4 je anatomicky tvarovaná a pevná, vďaka čomu dosahujú korčule vysokej odolnosti. Kolieskové korčule sú v strede koliesok osadené vysoko kvalitnými ložiskami ABEC 7. Korčule Tempish majú zaujímavý dizajn a tak vyzerajú naozaj veľmi moderne. Najdôležitejšie parametre inline korčúľ Tempish NERROW 4 green vo veľkosti 31 – 34 EU/188 – 214 mm

Objav podobné ako Tempish NERROW 4 green veľkosť 31 – 34 EU/188 – 214 mm (8592678086285)

Kolieskové korčule – detské, vhodné pre rekreačných korčuliarov, priemer koliesok: 70mm, tvrdosť koliesok: 82A, ložiská: ABEC 7, systém zaväzovania: šnúrky, sezóna 2019 Kvalitné kolieskové korčule značky Tempish NERROW 4 green vo veľkosti 35 – 38 EU/225 – 248 mm budú pre vás skvelým spoločníkom na vašich jazdách. Inline korčule od renomovaného výrobcu Tempish majú kolieska s priemerom 70 mm. Menšie kolieska s priemerom pod 83 mm nedosahujú síce tak vysokú rýchlosť, avšak sú viac stabilné, preto sa odporúčajú aj pre začiatočníkov. Konštrukcia korčúľ Tempish NERROW 4 je anatomicky tvarovaná a pevná, vďaka čomu dosahujú korčule vysokej odolnosti. Kolieskové korčule sú v strede koliesok osadené vysoko kvalitnými ložiskami ABEC 7. Korčule Tempish majú zaujímavý dizajn a tak vyzerajú naozaj veľmi moderne. Najdôležitejšie parametre inline korčúľ Tempish NERROW 4 green vo veľkosti 35 – 38 EU/225 – 248 mm

Objav podobné ako Tempish NERROW 4 green veľkosť 35 – 38 EU/225 – 248 mm (8592678086292)

Kolieskové korčule – detské, vhodné pre rekreačných korčuliarov, priemer koliesok: 70mm, tvrdosť koliesok: 82A, ložiská: ABEC 7, systém zaväzovania: šnúrky, sezóna 2019 Kvalitné kolieskové korčule značky Tempish NERROW 4 green vo veľkosti 39 – 42 EU/253 – 273 mm budú pre vás skvelým spoločníkom na vašich jazdách. Inline korčule od renomovaného výrobcu Tempish majú kolieska s priemerom 70 mm. Menšie kolieska s priemerom pod 83 mm nedosahujú síce tak vysokú rýchlosť, avšak sú viac stabilné, preto sa odporúčajú aj pre začiatočníkov. Konštrukcia korčúľ Tempish NERROW 4 je anatomicky tvarovaná a pevná, vďaka čomu dosahujú korčule vysokej odolnosti. Kolieskové korčule sú v strede koliesok osadené vysoko kvalitnými ložiskami ABEC 7. Korčule Tempish majú zaujímavý dizajn a tak vyzerajú naozaj veľmi moderne. Najdôležitejšie parametre inline korčúľ Tempish NERROW 4 green vo veľkosti 39 – 42 EU/253 – 273 mm

Objav podobné ako Tempish NERROW 4 green veľkosť 39 – 42 EU/253 – 273 mm (8592678086308)

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Potrebujete na motorku pripevniť svoj telefón? Hodiť sa vám tak rozhodne bude držiak na mobil RAM Mounts. Stojan na mobil je pripravený na mechanické upevnenie telefónu. Dáte do neho telefón so šírkou od 4,8 do 8,3 cm. Držiak mobilu na motorku vám dobre poslúži na cestách. Hlavné prednosti držiaka na mobil RAM Mounts kompletná zostava univerzálneho držiaka X-Grip na riadidlá do priemeru 60 mm Vďaka držiaku na mobil RAM Mounts budete mať telefón stále na očiach Je určený pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón nasadíte na držiak ručne Držiak telefónu RAM Mounts je pripravený na motorku

Objav podobné ako RAM Mounts kompletná zostava univerzálneho držiaka X-Grip na riadidlá do priemeru 60 mm (M021-007)

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Chcete na motorku pripevniť telefón? Osloviť vás môže držiak na mobil RAM Mounts. Stojan na mobil má z výroby nachystané mechanické upevnenie telefónu. Prichytíte do neho telefón so šírkou od 4,8 až do 8,3 cm. Držiak mobilu na motorku oceníte pri cestovaní. Zásadné vlastnosti držiaka na mobil RAM Mounts kompletná zastava držiaku mobilného telefonu „X-Grip" s uchytením na 9 mm skurtku Pomocou držiaka na mobil RAM Mounts budete mať telefón stále poruke Hodí sa pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón prichytíte k držiaku mechanicky Držiak telefónu RAM Mounts je nachystaný na motorku

Objav podobné ako RAM Mounts kompletná zastava držiaku mobilného telefonu „X-Grip s uchytením na 9 mm skurtku (M021-058)

RAM Mounts rameno pre 1,5" guľové čapy EAN: 793442001215 Prehľad RAM Mounts rameno s celkovou dĺžkou 143 mm je navrhnuté pre 1,5" guľové čapy. Pružina a uťahovacia skrutka na ramene umožňujú rýchle a pevné pripevnenie. Špecifikácia Rozmery: celková dĺžka 14,3 cm, dĺžka medzi svorkami 11,4 cm Materiál: povlakovaná zliatina hliníka Váha: 322 g Veľkosť guľového čapu: 1,5", gumový, veľkosti "C" Rady a nosnosti RAM vyrába svoj systém úchytov a ramien v niekoľkých radoch, odstupňovaných podľa nosnosti. Diely v rade "C" sú určené pre zariadenia do hmotnosti 4,5 kg. O systéme držiakov RAM mount Systém RAM poskytuje jedinečnú variabilitu vďaka patentovanému systému guľových čapov a ramien so svorkami. Užívateľ si tak môže zostaviť držiak pre svoje zariadenie podľa svojej potreby. Kovový vs. plastový diel Výhodou dielov z vysokopevnostného plastu je nižšia hmotnosť a cena, zatiaľ čo diely z povlakovanej zliatiny hliníka ponúkajú prémiový vzhľad. RAM mount garantuje pre oba typy dielov rovnaké pevnostné parametre a poskytuje na ne rovnakú doživotnú záruku. O RAM mount Produkty RAM mount sú navrhnuté tak, aby bezpečne uchytili elektronické prístroje tam, kde ich ľudia potrebujú. Výrobca kladie dôraz na vysokú kvalitu a spoľahlivosť.

Objav podobné ako RAM Mounts rameno pre 1,5" guľové čapy (celková dĺžka: 143 mm),

RAM Mounts rameno krátke, kovové, pre 1" guľové čapy EAN: 793442120114 Detaily produktu Vyrobené z: Povlakované zliatiny hliníka. Dĺžka: Celková dĺžka je 60,5 mm. Upínanie a kompatibilita Ručné upínanie pre jednoduchú manipuláciu. Kompatibilný s 1" guľovými čapmi. Priestor medzi svorkami 44,5 mm priestoru medzi svorkami na optimálne uchytenie. Prečo si vybrať RAM Mounts? Odolné a spoľahlivé riešenie na uchytenie. Jednoduché ovládanie vďaka ručnému upínaniu. Kompatibilný so širokou škálou zariadení.

Objav podobné ako RAM Mounts rameno krátke, kovové, pre 1" guľové čapy (celková dĺžka 60 mm), RAM-B-201U-A

RAM Mounts držiak VESA 75x75 mm, s 1,5" guľovým čapom, RAM-2461U EAN: 793442024610 Prehľad Držiak VESA 75x75 mm s 1,5" guľovým čapom. Štvorcová doštička držiaka s rozmermi 92x92 mm. Čap umiestnený 22 mm od stredu hrany. Použitie VESA 75x75 držiak pre LCD monitory, priemyselné PC, terminály atď. Úchyt na rovnú plochu so širokou podstavou pre rad "C" ramien a držiakov RAM s 1,5" čapy. Prednosti Kompatibilný so systémom ramien a úchytov RAM mount radu "C". Zodpovedá štandardu VESA 75x75. Dokonalé spracovanie. Doživotná záruka RAM mount. Špecifikácia Materiál: Povlakovaná zliatina hliníka Váha: 182 g Veľkosť guľového čapu: 1,5", gumový, veľkosti "C" Poznámka: "U" v čísle dielu znamená, že výrobok je balený v PU sáčku.

Objav podobné ako RAM Mounts držiak VESA 75x75 mm, s 1,5" guľovým čapom, RAM-2461U

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Potrebujete na motorku pripevniť telefón? Vhodným riešením pre vás môže byť držiak na mobil RAM Mounts. Stojan na mobil je z výroby pripravený na mechanické upevnenie telefónu. Vložíte do neho telefón so šírkou od 4,8 až do 8,3 cm. Držiak mobilu na motorku vám spríjemní cestovanie. Hlavné vlastnosti držiaka na mobil RAM Mounts kompletná zostava držiaku X-Grip s uchytením do krku riadenia motocykla Vďaka držiaku na mobil RAM Mounts budete mať telefón stále poruke Je určený pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón umiestnite do držiaka ručne Držiak telefónu RAM Mounts je pripravený na motorku

Objav podobné ako RAM Mounts kompletná zostava držiaku X-Grip s uchytením do krku riadenia motocykla (M021-073)

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11U: Compatible with OEM hand strap Easy insertion and removal With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-CAU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-C USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPT-CAU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-1AU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-A 1.1 (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM60CPN-1AU holder is supplied.

Objav podobné ako RAM Mounts EZ-Roll

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-CAU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-C USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM60CPN-CAU holder is supplied.

Objav podobné ako RAM Mounts EZ-Roll

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C and USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLN-CAU: Compatible with accessories and side accessory attachments Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Output Connector: USB-C USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLN-CAU holder is supplied.

Objav podobné ako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Modular Form-Fit holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLN-CU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Output Connector: USB-C (Peripheral output - 500mAh) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLN-CU holder is supplied.

Objav podobné ako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. The included RAM NFC extender supports the NFC function with a range of up to 30 cm. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, GDS Roto-Mag and side accessory attachments. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKL-NFCU: Compatible with accessories Including RAM NFC-Extender Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKL-NFCU holder is supplied.

Objav podobné ako RAM Mounts Form- Fit Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLNU: Compatible with accessories and side accessory attachments Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLNU holder is supplied.

Objav podobné ako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLT-AU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral data support is provided by the built-in dual USB-A RJ45 (ethernet) cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-RJ45AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A RJ45 (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLT-RJ45AU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLTU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLTU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-1AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPT-1AU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3

RAM Mounts adaptér s AMPS vzorom dier Adaptér RAM Mounts je vyrobený z povlakovanej zliatiny hliníka a je vybavený 1" gumovým čapom veľkosti "B". Výhodný a univerzálny Adaptér je kompatibilný so systémom ramien a úchytov RAM mount. Zodpovedá štandardu AMPS a poskytuje doživotnú záruku RAM mount. Použitie adaptéra Adaptér slúži ako úchyt na rovné povrchy s 1" čapom. Je určený pre pevné nerozoberateľné pripevnenie držiaka na rovnú plochu. Pripevnenie na palubnú dosku nákladného auta Pripevnenie na palubu lode Pripevnenie na board kajaku Adaptér tiež slúži ako prepojenie držiakov RAM s ramenami pre 1" čapy, najmä pre ťažšie univerzálne držiaky pre veľké tablety. Technické informácie Adaptér má priemer 6,35 cm a je vybavený 7 predvŕtanými dierami, z ktorých 4 zodpovedajú priemyselnému vzoru dier AMPS. Jeho hmotnosť je 68 g. Kovový verzus plastový diel RAM mount garantuje pre plastové aj kovové diely rovnaké pevnostné parametre. Sú plne zameniteľné. Výhodou plastových dielov je nižšia hmotnosť a cena, zatiaľ čo kovové diely ponúkajú prémiový vzhľad.

Objav podobné ako RAM Mounts adaptér, kovový, AMPS vzor dier, čap 1"

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PU holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8

This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PU holder is supplied.

Objav podobné ako RAM Mounts GDS EZ-Roll

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE21PDU holder is supplied.

Objav podobné ako RAM Mounts GDS EZ-Roll

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PDU holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8

This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PNLLU:Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKNLL-ZE21PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PNLLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET40/45 (10

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM NFC Extender can be used to expand the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3NU:Easy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for the RAM NFC ExtenderAdditional information: This holder version will not support the Getac Rotating Hand Strap Kickstand accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE3NU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Getac ZX70