ram mounts kompletna zostava drziaku x grip s uchytenim do krku riadenia motocykla m021 073

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Potrebujete na motorku pripevniť telefón? Vhodným riešením pre vás môže byť držiak na mobil RAM Mounts. Stojan na mobil je z výroby pripravený na mechanické upevnenie telefónu. Vložíte do neho telefón so šírkou od 4,8 až do 8,3 cm. Držiak mobilu na motorku vám spríjemní cestovanie. Hlavné vlastnosti držiaka na mobil RAM Mounts kompletná zostava držiaku X-Grip s uchytením do krku riadenia motocykla Vďaka držiaku na mobil RAM Mounts budete mať telefón stále poruke Je určený pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón umiestnite do držiaka ručne Držiak telefónu RAM Mounts je pripravený na motorku

Objav podobné ako RAM Mounts kompletná zostava držiaku X-Grip s uchytením do krku riadenia motocykla (M021-073)

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Chcete na motorku pripevniť telefón? Osloviť vás môže držiak na mobil RAM Mounts. Stojan na mobil má z výroby nachystané mechanické upevnenie telefónu. Prichytíte do neho telefón so šírkou od 4,8 až do 8,3 cm. Držiak mobilu na motorku oceníte pri cestovaní. Zásadné vlastnosti držiaka na mobil RAM Mounts kompletná zastava držiaku mobilného telefonu „X-Grip" s uchytením na 9 mm skurtku Pomocou držiaka na mobil RAM Mounts budete mať telefón stále poruke Hodí sa pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón prichytíte k držiaku mechanicky Držiak telefónu RAM Mounts je nachystaný na motorku

Objav podobné ako RAM Mounts kompletná zastava držiaku mobilného telefonu „X-Grip s uchytením na 9 mm skurtku (M021-058)

Držiak na mobil – na motorku, mechanický, pre mobily so šírkou 4,8 – 8,3 cm Potrebujete na motorku pripevniť svoj telefón? Hodiť sa vám tak rozhodne bude držiak na mobil RAM Mounts. Stojan na mobil je pripravený na mechanické upevnenie telefónu. Dáte do neho telefón so šírkou od 4,8 do 8,3 cm. Držiak mobilu na motorku vám dobre poslúži na cestách. Hlavné prednosti držiaka na mobil RAM Mounts kompletná zostava univerzálneho držiaka X-Grip na riadidlá do priemeru 60 mm Vďaka držiaku na mobil RAM Mounts budete mať telefón stále na očiach Je určený pre mobilný telefón so šírkou od 4,8 do 8,3 cm Telefón nasadíte na držiak ručne Držiak telefónu RAM Mounts je pripravený na motorku

Objav podobné ako RAM Mounts kompletná zostava univerzálneho držiaka X-Grip na riadidlá do priemeru 60 mm (M021-007)

kompletná kúpeľňová zostava s umývadlom a doskou
komplet kúpeľňová zostava s umývadlom a sifónom
kompletná kúpeľňová zostava v jednej krabici
kompletná kúpeľňová zostava so sifónom
komplet kúpeľňová zostava sifón
kompletná kúpeľňová zostava SAT
kompletná kúpeľňová zostava s doskou pod umývadlo
komplet kúpeľňová zostava biela
kompletná kúpeľňová zostava v tmavej farbe
vaňa Geberit 554.073.01.1
zlatá páková batéria do vane s podomietkovým uchytením
obojok pre psa s obvodom krku do 46,5 cm
rám na montáž armatúr do steny
Kaldewei Arrondo štvrťkruh rám do 100x100 cm
chrómové držiaky na uteráky do kúpeľne
montážny rám do sadrokartónovej konštrukcie

Držiak na mobil do krku riadenia, bezpečne udrží telefón, telo držiaku z pevnej a ľahkej zliatiny hliníka - duralu 6061, adaptér: S-Ball - pre uchytenie do krku riadenia, materiál: zliatina hliníka, nerez oceľ, guma, rýchle a jednoduché upevnenie i vybratie telefónu, rotácie 360 stupňov, nastavenie sklonu telefónu nahor, nadol a do strán, rozsah držiaku: šírka telefónu 60 - 100 mm, odporúčaná hrúbka pre optimálne uchytenie max. 10 mm, obsah balenia: držiak telefónu, S-Ball adaptér, polohovacie koleno DržiakM-Style AW 2 zaistí pevné uchytenie mobilného telefónu na vašej motorke. Jeho telo je vyrobené z pevnej a ľahkej zliatiny hliníka. Držiak ponúka veľmi rýchle a jednoduché upevnenie aj vybratie telefónu a 360° rotáciu, vďaka čomu možno nastaviť sklon telefónu nahor, nadol a do strán. Pojme pritom telefóny so šírkou 60 – 100 mm a súčasťou balenia je okrem samotného držiaka a polohovacieho kolena tiež adaptér S-ball, ktorý je určený na uchytenie do krku riadenia....

Objav podobné ako M-Style AW 2 celokovový držiak telefónu do krku riadenia – Veľkosť S-Ball adaptéra: O23 mm (3830-MS-198573-1339)

Držiak na mobil do krku riadenia, bezpečne udrží telefón, telo držiaku z pevnej a ľahkej zliatiny hliníka - duralu 6061, adaptér: S-Ball - pre uchytenie do krku riadenia, materiál: zliatina hliníka, nerez oceľ, guma, rýchle a jednoduché upevnenie i vybratie telefónu, rotácie 360 stupňov, nastavenie sklonu telefónu nahor, nadol a do strán, rozsah držiaku: šírka telefónu 60 - 100 mm, odporúčaná hrúbka pre optimálne uchytenie max. 10 mm, obsah balenia: držiak telefónu, S-Ball adaptér, polohovacie koleno Držiak M-Style AW 2 zaistí pevné prichytenie mobilného telefónu na vašej motorke. Jeho telo je vyrobené z pevnej a ľahkej zliatiny hliníka. Držiak ponúka veľmi rýchle a jednoduché upevnenie aj vybratie telefónu a 360° rotáciu, vďaka čomu možno nastaviť sklon telefónu nahor, nadol a do strán. Pojme pritom telefóny so šírkou 60 – 100 mm a súčasťou balenia je okrem samotného držiaka a polohovacieho kolena tiež adaptér S-ball, ktorý je určený na prichytenie do...

Objav podobné ako M-Style AW 2 celokovový držiak telefónu do krku riadenia – Veľkosť S-Ball adaptéra : O17,6 mm (3830-MS-198573-1338)

Držiak na mobil do krku riadenia, bezpečne udrží telefón, celokovové telo s pogumovanými hákmi a chrbtom proti poškriabaniu, adaptér: S-Ball - pre uchytenie do krku riadenia, jednoduché vloženie a vybratie vďaka tuhému pružinovému systému, rotácia 360 stupňov, nastavenie sklonu telefónu nahor a nadol a do strán, rozsah držiaku: nastaviteľná šírka bokov 57- 92 mm a nastaviteľná výška 132-170 mm, maximálna šírka telefónu 92 mm, výška 170 mm, hrúbka 19 mm, obsah balenia: držiak telefónu, S-Ball adaptér, polohovacie koleno Držiak M-Style Spine zaistí pevné prichytenie mobilného telefónu na vašej motorke. Jeho telo je vyrobené z kovu a doplnené o pogumované háky a chrbát zamedzujúci poškriabaniu. Držiak ponúka vďaka tuhému pružinovému systému veľmi rýchle vloženie aj vybratie telefónu a tiež 360° rotáciu, pomocou ktorej možno nastaviť sklon telefónu nahor, nadol a do strán. Pojme pritom telefóny do šírky 92 mm a súčasťou balenia je okrem samotného držiaka a...

Objav podobné ako M-Style Spine držiak na telefón do krku riadenia – Veľkosť S-Ball adaptéra: O15,8 mm (3834-MS-198771-1337)

Držiak na mobil do krku riadenia, bezpečne udrží telefón, celokovové telo s pogumovanými hákmi a chrbtom proti poškriabaniu, adaptér: S-Ball - pre uchytenie do krku riadenia, jednoduché vloženie a vybratie vďaka tuhému pružinovému systému, rotácia 360 stupňov, nastavenie sklonu telefónu nahor a nadol a do strán, rozsah držiaku: nastaviteľná šírka bokov 57- 92 mm a nastaviteľná výška 132-170 mm, maximálna šírka telefónu 92 mm, výška 170 mm, hrúbka 19 mm, obsah balenia: držiak telefónu, S-Ball adaptér, polohovacie koleno Držiak M-Style Spine zaistí pevné uchytenie mobilného telefónu na vašej motorke. Jeho telo je vyrobené z kovu a doplnené o pogumované háky a chrbát zamedzujúci poškriabaniu. Držiak ponúka vďaka tuhému pružinovému systému veľmi rýchle vloženie aj vybratie telefónu a tiež 360° rotáciu, pomocou ktorej možno nastaviť sklon telefónu nahor, nadol a do strán. Pojme pritom telefóny do šírky 92 mm a súčasťou balenia je okrem samotného držiaka a...

Objav podobné ako M-Style Spine držiak na telefón do krku riadenia – Veľkosť S-Ball adaptéra: O17,6 mm (3834-MS-198771-1338)

Držiak na mobil do krku riadenia, bezpečne udrží telefón, celokovové telo s pogumovanými hákmi a chrbtom proti poškriabaniu, adaptér: S-Ball - pre uchytenie do krku riadenia, jednoduché vloženie a vybratie vďaka tuhému pružinovému systému, rotácia 360 stupňov, nastavenie sklonu telefónu nahor a nadol a do strán, rozsah držiaku: nastaviteľná šírka bokov 57- 92 mm a nastaviteľná výška 132-170 mm, maximálna šírka telefónu 92 mm, výška 170 mm, hrúbka 19 mm, obsah balenia: držiak telefónu, S-Ball adaptér, polohovacie koleno Držiak M-Style Spine zaistí pevné prichytenie mobilného telefónu na vašej motorke. Jeho telo je vyrobené z kovu a doplnené o pogumované háky a chrbát zamedzujúci poškriabaniu. Držiak ponúka vďaka tuhému pružinovému systému veľmi rýchle vloženie aj vybratie telefónu a tiež 360° rotáciu, pomocou ktorej možno nastaviť sklon telefónu nahor, nadol a do strán. Pojme pritom telefóny do šírky 92 mm a súčasťou balenia je okrem samotného držiaka a...

Objav podobné ako M-Style Spine držiak na telefón do krku riadenia – Veľkosť S-Ball adaptéra: O23 mm (3834-MS-198771-1339)

Držiak na mobil do krku riadenia, bezpečne udrží telefón, celokovové telo s pogumovanými hákmi a chrbtom proti poškriabaniu, adaptér: S-Ball - pre uchytenie do krku riadenia, jednoduché vloženie a vybratie vďaka tuhému pružinovému systému, rotácia 360 stupňov, nastavenie sklonu telefónu nahor a nadol a do strán, rozsah držiaku: nastaviteľná šírka bokov 57- 92 mm a nastaviteľná výška 132-170 mm, maximálna šírka telefónu 92 mm, výška 170 mm, hrúbka 19 mm, obsah balenia: držiak telefónu, S-Ball adaptér, polohovacie koleno Držiak M-Style Spine zaistí pevné prichytenie mobilného telefónu na vašej motorke. Jeho telo je vyrobené z kovu a doplnené o pogumované háky a chrbát zamedzujúci poškriabaniu. Držiak ponúka vďaka tuhému pružinovému systému veľmi rýchle vloženie aj vybratie telefónu a tiež 360° rotáciu, pomocou ktorej možno nastaviť sklon telefónu nahor, nadol a do strán. Pojme pritom telefóny do šírky 92 mm a súčasťou balenia je okrem samotného držiaka a...

Objav podobné ako M-Style Spine držiak na telefón do krku riadenia – Veľkosť S-Ball adaptéra: O12,8 mm (3834-MS-198771-1336)

VitrA Mia je nástenná kúpeľňová zostava v lesklej bielej farbe s keramickým umývadlom. Šírka skrinky s umývadlom je 40 cm. Sada obsahuje umývadlovú batériu, vtok a sifón.

• Nástenná zostava šetrí miesto v kúpeľni.
• Lesklý bielý povrch je ľahko čistiteľný a moderný.
• Kompletná sada vrátane batérie, vtoku a sifónu.
• Keramické umývadlo je odolné a hygienické.

Objav podobné ako VitrA Mia kúpeľňová zostava s umývadlom vrátane umývadlovej batérie, vtoku a sifónu KSETMIA40B

Závesný WC set obsahuje modul pre montáž do ľahkých stien alebo predstenovú konštrukciu, nádržku TECE a WC sedátko. WC doska je vyrobená z odolného materiálu Duroplast. Ovládacie tlačidlo je z plastu a má povrchovú úpravu chrómový lesk.

• Kompletná sada pre jednoduchú montáž
• Vysokokvalitná Duroplast doska na WC
• Moderné ovládacie tlačidlo v chrómovom lesku

Objav podobné ako Cenovo zvýhodnený závesný WC set TECE do ľahkých stien / predstenová montáž + WC S-Line S-line Pre KMPLSIKOTSCR

RAM Mounts X-Grip univerzálny držiak na mobilný telefón EAN: 793442932298 Popis produktu RAM Mounts X-Grip je univerzálny držiak na mobilný telefón s 1" guľovým čapom. Skladá sa z pružinového mechanizmu, ktorý bezpečne udrží váš telefón. Držiak je doplnený zaisťovacou gumou pre maximálne bezpečie vášho zariadenia. Špecifikácia Šírka telefónu: 48 – 83 mm Hrúbka telefónu: do 22 mm Materiál: Nerez oceľ, povlakovaná zliatina hliníka, vysokopevnostný plast Váha: 100 g Veľkosť guľového čapu: 1", gumový, veľkosti „B“ Výhody produktu Držiak X-Grip ponúka bezpečné uchopenie telefónu aj pri vibráciách. Je univerzálny a kompatibilný so systémom ramien a úchytov RAM mount. Ponúka rýchle a jednoduché upevnenie aj vybratie telefónu. Je nehrdzavejúci a dodáva sa s doživotnou zárukou RAM mount. Upozornenie: X-Grip je súčasťou trojdielneho riešenia. Na zostavenie celého riešenia potrebujete okrem tohto držiaka ešte rameno a úchyt.

Objav podobné ako RAM Mounts X-Grip univerzálny držiak na mobilný telefón s 1" guľovým čapom

RAM Mounts X-Grip Univerzálny Držiak pre Veľké Telefóny EAN: 793442940873 Popis produktu Univerzálny držiak X-Grip je navrhnutý pre bezpečné uchytenie mobilných telefónov a smartfónov s veľkosťou väčšou ako 5". Bezpečnosť a pohodlie Držiak je vybavený pružinovým mechanizmom a gumovou podložkou, ktoré zaisťujú bezpečnosť a pohodlie vášho telefónu. Zaisťovacia guma Súčasťou balenia je zaisťovacia guma, ktorá zabraňuje vypadnutiu telefónu aj v extrémnych podmienkach. Rozsah držiaka Šírka telefónu: 44 - 114 mm Hrúbka telefónu: do 22 mm Overte si, že rozmery vášho telefónu sú menšie ako rozsah držiaka. Materiál Držiak je vyrobený z nerez ocele, povlakovanej zliatiny hliníka a vysokopevnostného plastu. Veľkosť guľového čapu Guľový čap má priemer 1" a je kompatibilný so všetkými "B" veľkosťami RAM mount ramien. Váha Držiak váži 114 g. Prednosti držiaka XGrip Bezpečne drží telefón aj pri vibráciách Univerzálna pre telefóny v puzdre aj bez Rýchle a jednoduché upevnenie a vybratie telefónu Kompatibilný so systémom ramien a úchytov RAM mount Nehrdzavejúci Doživotná záruka RAM mount Upozornenie X-Grip je časť trojdielneho riešenia. Okrem tohto držiaka potrebujete ešte rameno a úchyt na zostavenie celého riešenia.

Objav podobné ako RAM Mounts X-Grip univerzálny držiak na veľké telefóny s 1" guľovým čapom, RAM-HOL-UN10BU

RAM Mounts X-Grip Clamp Bracket for Smartphones up to 82.6 mm Width - Tough-Claw small (diameter 15.9-29.0 mm), direct X-Grip connection

Objav podobné ako RAM Mounts X-Grip Clamp Bracket

RAM Mounts X-Grip Handlebar Mount for Smartphones up to 82.6 mm Width - B-Ball (1 Inch), Screw Clamp, Middle Link Arm

Objav podobné ako RAM Mounts X-Grip Handlebar Mount

RAM Mounts X-Grip Bracket for Tablets (7 inches) - C-Ball (1.5 inches)

Objav podobné ako RAM Mounts X-Grip Bracket

RAM Mounts X-Grip Bracket for Tablets (7-8 Inch) - B-Ball (1 Inch)

Objav podobné ako RAM Mounts X-Grip Bracket

RAM Mounts X-Grip Bracket for Tablets (10 inches) - AMPS Connection

Objav podobné ako RAM Mounts X-Grip Bracket

RAM Mounts X-Grip Retaining Clip for Smartphones Large up to 114.3 mm Width - B-Ball

Objav podobné ako RAM Mounts X-Grip Retaining Clip

RAM Mounts X-Grip Bracket for Tablets (12 inches) - AMPS Connection

Objav podobné ako RAM Mounts X-Grip Bracket

RAM Mounts X-Grip Bracket for Smartphones Small to 82.6mm Width - B-Ball

Objav podobné ako RAM Mounts X-Grip Bracket

RAM Mounts X-Grip Tube Bracket for Tablets (10 inches) - C-Ball (1.5 inches), Double Screw Terminal (up to 31.8 mm Diameter), Middle Connection Arm

Objav podobné ako RAM Mounts X-Grip Tube Bracket

RAM Mounts X-Grip Suction Base Holder for Tablets (10 inches) - B-Ball (1 Inch), Medium Connection Arm

Objav podobné ako RAM Mounts X-Grip Suction Base Holder

RAM Mounts X-Grip Suction Base Bracket for Tablets (7 inches) - B-Ball (1 Inch), Medium Link Arm

Objav podobné ako RAM Mounts X-Grip Suction Base Bracket

RAM Mounts Power Grip XL - Large Universal Scanner Mounting Bracket (Composite), AMPS Connection, Screw Set, in Poly Bag

Objav podobné ako RAM Mounts Power Grip XL

RAM Mounts Quick-Grip™ XL Universal Mounting Bracket for Large Smartphones - with Diamond Base Plate (Trapezoid), B-Ball (1 Inch), Screw Set

Objav podobné ako RAM Mounts Quick-Grip™ XL Universal Mounting Bracket

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM NFC Extender can be used to expand the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3NU:Easy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for the RAM NFC ExtenderAdditional information: This holder version will not support the Getac Rotating Hand Strap & Kickstand accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE3NU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Getac ZX70

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PD2U:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp- Right or NFC-RepeaterInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PDLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PDLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Zebra ET80/85

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22LU:Compatible with accessoriesEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22LU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2HU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM Vent-Temp can utilize the vehicle's air vents to direct hot or cold air to the Getac ZX70.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3FU:Compatible with the Getac tablet accessoiresEasy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-TempAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-GE3FU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Getac ZX70

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU:Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25LU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable & DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 & DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE & FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A/DB-Sub-Anschluss

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE & FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender & RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE & FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A Connector