zebra p1014125 universal roll holder

Zebra P1014125 universal roll holder

Objav podobné ako Zebra P1014125 universal roll holder

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-Locking) for Zebra L10

This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDCLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10

Grohe Vitalio Universal sprchová tyč lepenie vŕtanie
Grohe Vitalio Universal sprchová tyč s držiakom
Hansgrohe uBox Universal nerez
Grohe Vitalio Universal 90 cm
rošt Alca zebra dekor
nerezová mriežka zebra vzor
kuchynský rošt zebra dekorácia
Ravak Roll zástena chróm X786D0C00Z1
rošt Alca 85 cm zebra dekor
nerezový rošt s mriežkou zebra
rošt zebra vzor nerez
nerezový rošt s dekorom zebra
sprchový žľab zebra dekor šedá lesk
sprchový žľab s mriežkou zebra
lesklý sprchový žľab zebra
nerezový sprchový žľab lesklý zebra

This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PCLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10

This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PD2CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PD2CLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10

External 98-0200021-00LF, Roll Holder

Objav podobné ako External 98-0200021-00LF, Roll Holder

External 98-0250064-00LF, Roll Holder

Objav podobné ako External 98-0250064-00LF, Roll Holder

Zebra 21-52612-01R Holder, rugged

Objav podobné ako Zebra 21-52612-01R Holder, rugged

Zebco Držiak prútu Rod holder X-long 128 cm

Objav podobné ako Zebco držiak prútu rod holder x-long 128 cm

Zebra PolyE 3100T, rolka štítkov, syntetická (polyetylén), lesklá, termotransferová, šírka rolky: 102mm, jadro: 25mm, rozmery (ŠxV): 102x76mm, 800 štítkov/rolka, farba: biela.

Objav podobné ako Zebra 3011718, label roll, synthetic, 102mm, 102x76mm, white

Zebra PolyE 3100T, rolka štítkov, syntetická (polyetylén), lesklá, termotransferová, jadro: 76mm, rozmery (ŠxV): 102x51mm, 2590 štítkov/rolka, odporúčané. stuha: 4800 živica.

Objav podobné ako Zebra 3011702, label roll, synthetic, 102x51mm, biele

Zebra PolyE 3100T, rolka štítkov, syntetická (polyetylén), lesklá, termotransferová, jadro: 76mm, rozmery (ŠxV): 102x152mm, 950 štítkov/rolka, odporúčané. stuha: 4800 živica.

Objav podobné ako Zebra 3011713, label roll, synthetic, 102x152mm, white

Zebra PolyPro 3000T, rolka etikiet, syntetická (polypropylén), lesklá, pre stolné tlačiarne, jadro: 25,4mm, priemer: 127mm, rozmery (ŠxV): 51x25mm, 2905 etikiet/rolka, odporúčané. ribbon: 5095 živica.

Objav podobné ako Zebra 3011159, label roll, synthetic, 51x25mm, white

Zebra PolyPro 3000T, rolka etikiet, polypropylén, lesklý, jadro: 25mm, priemer: 127mm, rozmery (ŠxV): 55x35mm, 2100 etikiet/rolka.

Objav podobné ako Zebra 3012962, label roll, 55x35mm, transparentné

Roll-on dezodorant Tabac Original s klasickou pánskou vôňou, ktorá sa vyrába od roku 1959. Disponuje objemom 75 ml a je vhodný na každodenné používanie. Aplikácia roll-on umožňuje pohodlné a presné nanesenie.

• Klasická pánska vôňa vyrábaná od roku 1959.
• Roll-on aplikácia pre jednoduché a presné nanášanie.
• Objem 75 ml pre dlhodobé používanie.
• Vhodný pre každodennú starostlivosť o telo.

Objav podobné ako Tabac Original roll-on 75 ml

Recipe For Men Raw Naturals High Gear očný roll-on je chladiaci a ošetrujúci gél určený pre mužov. Produkt účinne redukuje opuchy a tmavé kruhy v oblasti očí. Jeho formulácia je zameraná na špecifické potreby mužskej pleti.

• Chladiaci efekt pre okamžitú úľavu
• Účinne znižuje opuchy a tmavé kruhy
• Špeciálne vyvinutý pre potreby mužskej pleti
• Prírodné zloženie šetrné k pokožke

Objav podobné ako Recipe For Men Raw Naturals očný roll-on 15 ml

Tento celonerezový chafing dish Roll-Top "CLASSIC" je vybavený dvoma nádobami na palivo a pokrievkou, ktorá sa otvára o 90°. Má rozmery 660x335x400 mm a objem 9 litrov, pričom je kompatibilný s vykurovacími spirálami ako model 430020. Je vhodný na udržiavanie teploty jedál v gastro prevádzkach.

• Celonerezová konštrukcia zaisťuje dlhú životnosť a jednoduché čistenie.
• Dve nádoby na palivo umožňujú dlhšie a efektívnejšie udržiavanie teploty.
• Pokrievka Roll-Top s otváraním o 90° uľahčuje prístup a manipuláciu s obsahom.
• Kompatibilita s vykurovacími spirálami (napr. 430020) ponúka flexibilitu pri ohreve.

Objav podobné ako STALGAST Chafing dish Roll-Top \"CLASSIC\"""

Plniteľný roll-on dezodorant Osma s objemom 50 ml využíva prírodné zloženie na reguláciu potenia. Vyznačuje sa jemnou sviežou vôňou. Jeho konštrukcia umožňuje opakované dopĺňanie.

• Plniteľný dizajn znižuje odpad
• Prírodné zloženie šetrné k pokožke
• Jemná svieža vôňa
• Prirodzene reguluje potenie

Objav podobné ako Osma plniteľný dezodorant roll-on 50 ml

Lea Men roll-on antiperspirant poskytuje účinnú celodennú ochranu pred potením. Je vhodný pre mužov a má praktické roll-on balenie. Produkt je od španielskej značky Lea.

• Celodenná ochrana pred potením a zápachom
• Vhodný pre citlivú pokožku, bez štipania
• Praktické roll-on balenie na presnú aplikáciu
• Španielska kvalita značky Lea

Objav podobné ako Lea Men roll-on antiperspirant 50 ml

Sprchový žľab Tece Linus s dĺžkou 70 cm je vyrobený z nerezu v lesklom prevedení. Má mriežku v dekore zebra a priemer odpadu DN 50. Balenie obsahuje sifón a montážne nohy.

• Vyrobený z odolného nerezu v lesklom prevedení.
• Dodáva sa s mriežkou v modernom dekore zebra.
• Súčasťou balenia je sifón a montážne nohy.
• Minimálna stavebná výška len 7 cm pre ľahšiu inštaláciu.

Objav podobné ako Tece Linus sprchový žľab 70 cm nerez lesk zebra 15100079 15.100.070

Sprchový žľab Tece Linus je vyrobený z nerezu s lesklým povrchom a šírkou roštu 84 cm. Jeho celková dĺžka je 90 cm a minimálna stavebná výška 7 cm. Súčasťou balenia je mriežka v dekore zebra, sifón, montážne nohy a odpad s priemerom DN 50.

• Vyrobený z kvalitného nerezu v lesklom prevedení.
• Dodáva sa s mriežkou v modernom dekore zebra.
• Súčasťou balenia je sifón a montážne nohy.
• Minimálna stavebná výška len 7 cm.

Objav podobné ako Tece Linus sprchový žľab 90 cm nerez lesk zebra 15100099 15.100.090

Thermal transfer ribbon, Zebra, 2300, wax, Roll-width: 156 mm, Core-width: 156 mm, Core: 25,4 mm, Length: 900 m, Ink side: Outside, Printhead: Flat-Head, Colour: Black

Objav podobné ako Thermal transfer ribbons, Zebra, 2300, wax, 156 mm, 900 m, Out, Black

Thermal transfer ribbon, Zebra, 5095, resin, Roll-width: 220 mm, Core-width: 220 mm, Core: 25,4 mm, Length: 450 m, Ink side: Outside, Printhead: Flat-Head, Colour: Black

Objav podobné ako Thermal transfer ribbons, Zebra, 5095, resin, 220 mm, 450 m, Out, Black

Thermal transfer ribbon, Zebra, 2300, wax, Roll-width: 170 mm, Core-width: 170 mm, Core: 25,4 mm, Length: 900 m, Ink side: Outside, Printhead: Flat-Head, Colour: Black

Objav podobné ako Thermal transfer ribbons, Zebra, 2300, wax, 170 mm, 900 m, Out, Black

Thermal transfer ribbon, Zebra, 1600, wax, Roll-width: 220 mm, Core-width: 220 mm, Core: 25,4 mm, Length: 450 m, Ink side: Outside, Printhead: Flat-Head, Colour: Black

Objav podobné ako Thermal transfer ribbons, Zebra, 1600, wax, 220 mm, 450 m, Out, Black

This RAM Mounts EZ-Roll‘r (key-locking) holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PKLU holder is supplied.

Objav podobné ako RAM Mounts EZ-Roll’r Holder (key-locking) for Zebra ET40/45 (8")

This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional informations: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20U.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, ... Unknown localization key: "more"

Objav podobné ako RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (8")

This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PU holder is supplied.

Objav podobné ako RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (8")

This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (10")

This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates extended battery packs and the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPDHU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Heated Pogo-Pins Lockable with key Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Holder (Key-Locking) for Zebra TC2x & TC5x Series in IntelliSkin Protective Sleeve - Heated Pogo-Pins - USB-C & USB-A Connector

This RAM Mounts GDS holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates extended battery packs and the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-V12-ZE2434CPDU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-V12-ZE2434CPDU holder is supplied.

Objav podobné ako RAM Mounts GDS Holder for Zebra TC2x & TC5x Series in IntelliSkin Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPDU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-V12-ZE16CPDU holder is supplied.

Objav podobné ako RAM Mounts GDS Holder for Zebra EC50 & EC55 in IntelliSkin Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 with Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PLU:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with KeysInput Connector: USB-A Input Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC22/27

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 without Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PL-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with keyInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PL-1U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC22/27

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU:Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25LU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-1AU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-A 1.1 (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support ... Unknown localization key: "more"

Objav podobné ako RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CPN-CAU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product ... Unknown localization key: "more"

Objav podobné ako RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts EZ-Roll‘r Form-Fit holder is suitable for Samsung Tab Active3 in an OtterBox uniVERSE case. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM60CP-OT1U: Compatible with accessories Can only be used with OtterBox uniVERSE case Access to the stylus pen Easy insertion and removal Charging function Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM60CP-OT1U holder is supplied.

Objav podobné ako RAM Mounts EZ-Roll'r Holder for Samsung Tab Active3 - In OtterBox uniVERSE Case- USB-C Connector

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PD2KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PD2KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8")

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts holder is suitable for Zebra ET5x 10.1“ Series with rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PDU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Zebra ET51/56 (10")