ram mounts modular form fit holder key locking for samsung tab active3 active5 in oem ram sleeve usb c connector

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLNU: Compatible with accessories and side accessory attachments Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLNU holder is supplied.

Objav podobné ako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C and USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLN-CAU: Compatible with accessories and side accessory attachments Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments. Modular docks are not compatible with the GDS Hand-Stand The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLN-CU: Compatible with accessories Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Output Connector: USB-C (Peripheral output - 500mAh) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Power & Data Connector

držiak s nabíjaním pre Samsung Tab A9+ v IntelliSkin Next Gen
držiak pre Samsung Tab A9+ s podporou periférií
RAM Mounts držiak s 15W nabíjaním
RAM Mounts nabíjacia stanica pre Honeywell CT40
RAM Mounts dokovacia stanica s VESA uchytením
univerzálna nabíjacia dokovacia stanica RAM Mounts
RAM Mounts nabíjacia stanica pre Honeywell RT10
upevnenie RAM Mounts pre Honeywell RT10
univerzálny držiak RAM Mounts do auta
RAM Mounts držiak s dvojitým otočným ramenom
tablet Samsung Galaxy Tab S11 s umelou inteligenciou
Samsung Galaxy TAB S7 FE tablet čierny
RAM-GDS-DOCKL-SAM88CDU držiak s USB-C a USB-A konektorom
polysan modular sprchová zástena walk-in 140 cm
polysan modular sprchová zástena walk-in 100 cm
polysan modular sprchová zástena walk-in 160 cm

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-CAU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-C & USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-1AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28" depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible ... Unknown localization key: "more"

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CP-NFCU: Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CP-NFCU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Cool-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKLF-SAM62CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Includes built-in 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKLF-SAM62CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Cool-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Connect

Tento RAM Mounts GDS Tough-Dock držiak s kľúčovým zámkom je určený pre Samsung Tab A9+ v IntelliSkin Next Gen ochrannom obale. Držiak nabíja tablet cez USB-C konektor a poskytuje USB-A port pre pripojenie periférií. Spodná časť držiaka je prispôsobená na pripevnenie na guľovú základňu.

• Bezpečné pripevnenie tabletu pomocou kľúčového zámku
• Nabíjanie tabletu cez USB-C konektor s výkonom 15W
• Podpora periférnych zariadení cez USB-A port
• Jednoduchá inštalácia a vyberanie tabletu

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. Data synchronization via the connection is also supported. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CU: Compatible with GDS hand-stand Easy insertion and removal Charging function Data synchronization Lockable with key Input Connector: USB-C 3.1 Power Output: 60W Output Voltage: 5-20V @ 3A Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active2, Active3 & Active5 - in IntelliSkin Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM88CD2U: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: 2x USB-A (Peripheral output - 900mAh per Port) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm · Prepared for GDS 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM88CD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Protective Sleeve - USB-C & Dual USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9 & A7 Lite 8.7" in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM80CD2U: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: 2x USB-A (Peripheral output - 900mAh per Port) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm · Prepared for GDS 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM80CD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9 & A7 Lite 8.7" - in IntelliSkin Protective Sleeve - USB-C & Dual USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A8 10.5" (SM-X200) in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM83CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM83CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A8 (10.5“) in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A8 10.5" (SM-X200) in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM83CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM83CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, Tab S9 & Tab S9 FE in IntelliSkin protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. Data synchronization via the connection is also supported. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM78CU: Compatible with GDS hand-stand Easy insertion and removal Charging function Data synchronization Lockable with key Input Connector: USB-C Power Output: 60W Output Voltage: 5-20V @ 3A Input Cable Length: ca. 35 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM78CU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ in IntelliSkin Protective Sleeve - USB-C Power Supp

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM80CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM80CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connect

This RAM Mounts GDS Cool-Dock (Key-Locking) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKLF-SAM78CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Includes built-in 12-VDC Axial cooling fan Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKLF-SAM78CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Cool-Dock Holder (Key-Locking) for Samsung Tab S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM80CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM80CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM76CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM76CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. Data synchronization via the connection is also supported. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM76CU: Compatible with GDS hand-stand Easy insertion and removal Charging function Data synchronization Lockable with key Input Connector: USB-C Power Output: 60W Output Voltage: 5-20V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM76CU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM78CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM78CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Case - USB-C Power Supply

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PU holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10")

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+- in IntelliSkin Next Gen Protective Sleeve - USB-C Connector

This RAM Mounts EZ-Roll‘r (key-locking) holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PKLU holder is supplied.

Objav podobné ako RAM Mounts EZ-Roll’r Holder (key-locking) for Zebra ET40/45 (8")

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM88CD2U: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A max Output Connector: 2x USB-A (Peripheral output - 900mAh per Port) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM88CD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM88CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM88CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDKLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (with key-locking) for Honeywell RT10

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A8 10.5" (SM-X200) in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM83CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM83CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A8 10.5" (SM-X200) in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM83CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM83CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C Connector

The RAM Mounts GDS Uni-Conn Snap-In Docking Station with Key-Locking (Left) is a versatile solution for devices equipped with an IntelliSkin Thin-Case protective sleeve with rear Pogo-Pads. This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection. The docking and undocking process is simple: Insert the tablet with the compatible IntelliSkin Thin-Case protective sleeve into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. The back of the dock is designed to accommodate a Diamond (Trapezoid) base plate (not included). This holder provides a reliable charging solution for various applications. Product features RAM Mounts RAM-GDS-DOCKLL-U3CPU: Only compatible with IntelliSkin and Rear Pogo-Pads Snap-In function Key-Locking Easy insertion and removal Charging function Input Connector: USB-C Power Output: 60W max Output voltage: 5 - 20V @ 3A max Input Cable Length: ca. 800 mm Weight: ca. 150 g Additional information: The Lever Stop included with this dock is required in order to function properly. Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Powered Snap-In Dock with Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C Connector - Screw Set

The RAM Mounts GDS Uni-Conn Snap-In Docking Station with Key-Locking (Rechts) is a versatile solution for devices equipped with an IntelliSkin Thin-Case protective sleeve with rear Pogo-Pads. This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection. The docking and undocking process is simple: Insert the tablet with the compatible IntelliSkin Thin-Case protective sleeve into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. The back of the dock is designed to accommodate a Diamond (Trapezoid) base plate (not included). This holder provides a reliable charging solution for various applications. Product features RAM Mounts RAM-GDS-DOCKLR-U3CPU: Only compatible with IntelliSkin and Rear Pogo-Pads Snap-In function Key-Locking Easy insertion and removal Charging function Input Connector: USB-C Power Output: 60W max Output voltage: 5 - 20V @ 3A max Input Cable Length: ca. 800 mm Weight: ca. 150 g Additional information: The Lever Stop included with this dock is required in order to function properly. Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Powered Snap-In Dock with Key-Locking (Rechts) - 2-Hole AMPS Pattern - USB-C Connector - Screw Set

The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Left) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter. This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection. With the dual USB-A port, you can integrate a peripheral device into your setup. The docking and undocking process is simple: Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case. Currently, the following devices are compatible with this fixed docking height: Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+. This holder provides a reliable solution for charging and data transfer across various applications. Product features RAM Mounts RAM-GDS-DOCKLL-U1CD2U: Only compatible with IntelliSkin & Uni-Conn adapter Snap-In function Key-Locking Easy insertion and removal Charging function & data transfer Input Connector: USB-C ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Charging Dock - Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C & Dual USB-A Connector - Screw Set

The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Left) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter. This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection. With the USB-C port, you can integrate a peripheral device into your setup. The docking and undocking process is simple: Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case. Currently, the following devices are compatible with this fixed docking height: Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+. This holder provides a reliable solution for charging and data transfer across various applications. Product features RAM Mounts RAM-GDS-DOCKLL-U1CP-CU: Only compatible with IntelliSkin & Uni-Conn adapter Snap-In function Key-Locking Easy insertion and removal Charging function Input Connector: USB-C Power Output: 15W Output ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Charging Dock with Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw Set

The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Right) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter. This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection. With the dual USB-A port, you can integrate a peripheral device into your setup. The docking and undocking process is simple: Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case. Currently, the following devices are compatible with this fixed docking height: Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+. This holder provides a reliable solution for charging and data transfer across various applications. Product features RAM Mounts RAM-GDS-DOCKLR-U1CD2U: Only compatible with IntelliSkin & Uni-Conn adapter Snap-In function Key-Locking Easy insertion and removal Charging function & data transfer Input Connector: USB-C ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Charging Dock - Key-Locking (Right) - 2-Hole AMPS Pattern - USB-C & Dual USB-A Connector - Screw Set

The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Right) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter. This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection. With the USB-C port, you can integrate a peripheral device into your setup. The docking and undocking process is simple: Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case. Currently, the following devices are compatible with this fixed docking height: Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+. This holder provides a reliable solution for charging and data transfer across various applications. Product features RAM Mounts RAM-GDS-DOCKLR-U1CP-CU: Only compatible with IntelliSkin & Uni-Conn adapter Snap-In function Key-Locking Easy insertion and removal Charging function Input Connector: USB-C Power Output: 15W Output ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Charging Dock with Key-Locking (Right) - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw Set

The RAM Mounts GDS Uni-Conn docking station with Key-Locking (Right) is a free-standing dock designed for devices enclosed in an IntelliSkin Next-Gen, IntelliSkin Hard Case, or IntelliSkin Thin-Case with a mounted GDS Uni-Conn adapter. This solution can swivel 180 degrees and allows the device to tilt 180 degrees, making it ideal for customer-centric industries like retail, hospitality, food service, and more. The snap-in holder keeps your device securely in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection while the two USB-A ports on the back support up to two input devices like keyboard, mouse, scanner gun, and more. The docking station features a weighted base and rubber pads that prevent it from sliding on surfaces. It also supports an easy docking and undocking process: Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the compatible IntelliSkin protective sleeve. Product features RAM-GDS-DOCKLR-D14-U1C-2A: Only compatible with IntelliSkin & ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Stand Docking Station with Key Locking (Right) - Rotatable & Tiltable - USB-C & Dual USB-A Connector

The RAM Mounts GDS Uni-Conn docking station with Key-Locking (Right) is a free-standing dock designed for devices enclosed in an IntelliSkin Next-Gen, IntelliSkin Hard Case, or IntelliSkin Thin-Case with a mounted GDS Uni-Conn adapter. This solution can swivel 180 degrees and allows the device to tilt 180 degrees, making it ideal for customer-centric industries like retail, hospitality, food service, and more. The snap-in holder keeps your device securely in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection while the two USB-A ports on the back support up to two input devices like keyboard, mouse, scanner gun, and more. The docking station features a weighted base and rubber pads that prevent it from sliding on surfaces. It also supports an easy docking and undocking process: Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the compatible IntelliSkin protective sleeve. Product features RAM-GDS-DOCKLR-D14-U1C-2A-GRY: Only compatible with IntelliSkin & ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Stand Docking Station with Key Locking (Right) - Rotatable & Tiltable - USB-C & Dual USB-A Connector - Gray

The RAM Mounts GDS Uni-Conn docking station with Key-Locking (Right) is a free-standing dock designed for devices enclosed in an IntelliSkin Thin-Case with Rear Pogo Pads. This solution can swivel 180 degrees and allows the device to tilt 180 degrees, making it ideal for customer-centric industries like retail, hospitality, food service, and more. The snap-in holder keeps your device securely in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection while the two USB-A ports on the back support up to two input devices like keyboard, mouse, scanner gun, and more. The docking station features a weighted base and rubber pads that prevent it from sliding on surfaces. It also supports an easy docking and undocking process: Insert the tablet with the IntelliSkin Thin-Case protective sleeve and Rear Pogo Pads into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. Product features RAM-GDS-DOCKLR-D14-U3C-2A: Only compatible with IntelliSkin Thin-Case (Rear Pogo Pads) Snap-In function Key-Locking Easy insertion and removal Charging function Output Voltage: 5V-20V @ 3A max (USB-C Tablets) Power Output: 60W max Input Connector: USB-C / ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Stand Docking Station with Key Locking (Right) - Rotatable & Tiltable - USB-C & Dual USB-A Connector - Rear Pogo Pads

The RAM Mounts GDS Uni-Conn docking station with Key-Locking (Right) is a free-standing dock designed for devices enclosed in an IntelliSkin Thin-Case with Rear Pogo Pads. This solution can swivel 180 degrees and allows the device to tilt 180 degrees, making it ideal for customer-centric industries like retail, hospitality, food service, and more. The snap-in holder keeps your device securely in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection while the two USB-A ports on the back support up to two input devices like keyboard, mouse, scanner gun, and more. The docking station features a weighted base and rubber pads that prevent it from sliding on surfaces. It also supports an easy docking and undocking process: Insert the tablet with the IntelliSkin Thin-Case protective sleeve and Rear Pogo Pads into the base of the dock and push it back until it snaps into place. To remove it, simply press the lever to release the tablet. Product features RAM-GDS-DOCKLR-D14-U3C-2A-GRY: Only compatible with IntelliSkin Thin-Case (Rear Pogo Pads) Snap-In function Key-Locking Easy insertion and removal Charging function Output Voltage: 5V-20V @ 3A max (USB-C Tablets) Power Output: 60W max Input Connector: USB-C / ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Uni-Conn Stand Docking Station with Key Locking (Right) - Rotatable & Tiltable - USB-C & Dual USB-A Connector - Rear Pogo Pads - Gray

This RAM Mounts GDS IntelliSkin Thin-Case charging protective cover is a slim, durable case for the Apple iPad Pro 12.9 (3.-5. Gen.) – designed specifically for the GDS Uni-Conn docking platform. It offers reliable protection combined with convenient charging functionality. An additional USB-C port at the bottom allows the device to be charged even without a dock. Thanks to its thoughtful design, all tablet functions remain accessible – including the camera and buttons. The IntelliSkin Thin-Case is exclusively compatible with GDS Uni-Conn mounts and docks. Product features RAM Mounts RAM-GDS-SKIN-AP37-TCD: Only compatible with GDS Uni-Conn Compatible with hand- & shoulder strap Continued access to camera and buttons Charging function Easy insertion and removal Ports: External USB-C 2.0 Transfer Speed: USB 3.1 @ 5 Gbps (via D-Shape-Contacs)* USB 2.0 @ 480 Mbps (via External USB-C Port) Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations. Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-AP37-TCD is supplied.

Objav podobné ako RAM Mounts IntellìSkin Thin Case for Apple iPad Pro 12.9 (3.-5. Gen.) - GDS-Technology - External USB-C Connector

This RAM Mounts GDS IntelliSkin Thin-Case charging protective cover is a slim, durable case for the Apple iPad Pro 11 (M4) with rear pogo pads – designed specifically for the GDS Uni-Conn docking platform. It offers reliable protection combined with convenient charging functionality. An additional USB-C port at the bottom allows the device to be charged even without a dock. The flat, ruggedized pogo pad contacts are optimized for frequent docking and are easy to clean. Thanks to its thoughtful design, all tablet functions remain accessible – including the camera and buttons. The IntelliSkin Thin-Case is exclusively compatible with GDS Uni-Conn mounts and docks. Product features RAM Mounts RAM-GDS-SKIN-AP45-M4-TCB: Only compatible with GDS Uni-Conn Compatible with hand- & shoulder strap Continued access to camera and buttons Charging function Easy insertion and removal Ports: External USB-C 2.0 Transfer Speed: USB 2.0 @ 480Mbps (via External USB-C Port) Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-AP45-M4-TCB is supplied.

Objav podobné ako RAM Mounts IntellìSkin Thin Case for Apple iPad Pro 11 (M4) - GDS-Technology - Rear Pogo-Pads - External USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM62CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the "No Battery Mode" function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-C cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62C-CU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-C (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM62C-CU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - Dual USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62CP-NFCU: Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM62CP-NFCU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector

This RAM Mounts GDS Cool-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKF-SAM62CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Includes built-in 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKF-SAM62CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Cool-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder with Multi-Mode is suitable for the Samsung Tab Active2, Active3 & Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. Mutli-mode is integrated into the dock allowing centralized AI systems to perform as the host instead of the tablet, turning your IntelliSkin-wrapped tablet into a peripheral. There is no button or switch that turns this function on and off—Multi-Mode is automatically activated when the device is docked. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62-MMU: Compatible with GDS hand-stand Easy insertion and removal Charging function Multi-mode With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A max (Peripheral: 5V - 900mA max) Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. ... Unknown localization key: "more"

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - Multi-Mode - USB-C & USB-A Co