ram mounts printer holder

RAM Mounts Printer Holder with Paper Guide for Zebra ZQ630 Series - 4-Bolt AMPS Exception

Objav podobné ako RAM Mounts Printer Holder

This RAM Mounts GDS holder is suitable for Zebra EC50 EC 55 with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPDU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-V12-ZE16CPDU holder is supplied.

Objav podobné ako RAM Mounts GDS Holder for Zebra EC50

This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x TC5x series with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates extended battery packs and the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPDHU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Heated Pogo-Pins Lockable with key Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-V12-ZE2434CPDHU holder is supplied.

Objav podobné ako RAM Mounts GDS Holder (Key-Locking) for Zebra TC2x

montážny rám Alca A104B/1200
nástenné armatúry montážny rám
rám pre batériu Alca A104B
rám pre nástenné armatúry pred stenou
Alca A104B montážny rám 1200
rám na montáž armatúr do steny
moderné dvere MDF rám s odolným povrchom
montážny rám pre madlo Alca A106/1120

This RAM Mounts GDS holder is suitable for Zebra TC2x TC5x series with the IntelliSkin protective sleeve. The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged. While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable. Available space in the back accommodates extended battery packs and the Zebra hand strap. The back of the device holder is prepared to support a diamond ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-V12-ZE2434CPDU: Only compatible with the IntelliSkin protective sleeve Spring-loaded design for easy insertion and removal Integrated Stylus holder Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 100 cm Additional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-V12-ZE2434CPDU holder is supplied.

Objav podobné ako RAM Mounts GDS Holder for Zebra TC2x

RAM Mounts scanner holder with magnetic Tough-Mag adapter

Objav podobné ako RAM Mounts scanner holder

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PD2KLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Input Voltage: 19V Output Voltage: 14V Input Cable Length: ca. 100 cm Output Cable Length: ca. 24 cm Certifications: FCC, IC, CE, UKCA, WEEE RoHS Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5PD2KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PD2U: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal With Latch Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Input Voltage: 19V Output Voltage: 14V Input Cable Length: ca. 100 cm Output Cable Length: ca. 24 cm Certifications: FCC, IC, CE, UKCA, WEEE RoHS Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX80 Rugged Tablet - 5.5mm DC

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PDKLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Input Voltage: 19V Output Voltage: 14V Input Cable Length: ca. 100 cm Output Cable Length: ca. 24 cm Certifications: FCC, IC, CE, UKCA, WEEE RoHS Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5PDKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PDU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal With Latch Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Connector Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Input Voltage: 19V Output Voltage: 14V Input Cable Length: ca. 100 cm Output Cable Length: ca. 24 cm Certifications: FCC, IC, CE, UKCA, WEEE RoHS Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX80 Rugged Tablet - 5.5mm DC

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-CAU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-C USB-A (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPT-CAU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. The included RAM NFC extender supports the NFC function with a range of up to 30 cm. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, GDS Roto-Mag and side accessory attachments. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKL-NFCU: Compatible with accessories Including RAM NFC-Extender Can only be used with OEM or RAM skin Access to the stylus pen Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This product will not support the No Battery Mode function. Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKL-NFCU holder is supplied.

Objav podobné ako RAM Mounts Form- Fit Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLT-AU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral data support is provided by the built-in dual USB-A RJ45 (ethernet) cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLT-RJ45AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Output Connector: USB-A RJ45 (Peripheral output - 900mAh per Port) Transfer-Speed: 480Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLT-RJ45AU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPKLTU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal Lockable with key Charging function Input Connector: USB-C Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPKLTU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 Active5 in OEM or RAM protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons allow you to continue using them without any problems. An RAM NFC-Extender module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-HOL-SAM58CPT-1AU: Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skin Slim-profile design at 2.28 depth Access to the stylus pen Optional attachment of additional devices or accessories Easy insertion and removal With Latch Charging function Input Connector: USB-C Output Connector: USB-A (Peripheral output - 500mAh) Transfer-Speed: 12Mbps Input Voltage: 5.3-5.4 VDC Output Voltage: 5 VDC Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag. Devices shown are not included in the delivery. Only the RAM-HOL-SAM58CPT-1AU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PU holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld s scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PHU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Honeywell CT40, CT45

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PDU holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld s scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDHU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Honeywell CT40, CT45

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld s scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld s scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Honeywell CT40, CT45

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PD2U:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp- Right or NFC-RepeaterInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PDLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PDLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Zebra ET80/85

This RAM Mounts Form-Fit holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2HU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder for Zebra ET60/65

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Getac ZX10

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld s scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld s scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDHLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE21PDU holder is supplied.

Objav podobné ako RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device s internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CP-NFCU: Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CP-NFCU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62CP-NFCU: Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM62CP-NFCU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (key-locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PKLU: Compatible with OEM hand strap Easy insertion and removal Charging function Lockable with key Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PDU: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: USB-A 2.0 (Peripheral output - 500mAh) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PDU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5KLU: Compatible with the Getac tablet accessoires Not compatible with the Getac hand strap accessory Easy insertion and removal Lockable with Keys Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5KLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used. The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Getac ZX80. An NFC repeater add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-GE5PKLU: Compatible with the Getac tablet accessoires Not compatible with the Getac 4-point hand strap accessory Easy insertion and removal Lockable with key Additional mounting plate for attaching additional devices or accessories Prepared for RAM Vent-Temp, Temp Right or NFC repeater Input Connector: 5.5mm DC-Buchse Input Voltage: 19V Output Voltage: 14V Input Cable Length: ca. 100 cm Certifications: FCC, IC, CE, UKCA, WEEE RoHS Additional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap. Devices shown are not included in the delivery. Only the RAM-HOL-GE5PKLU holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC Power Supply

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot. The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable DB9 connector. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The cradle also allows the tablet s scanning function to continue to be used because of the cutout at the back. RAM Vent-Temp utilizes the vehicle s vents to direct hot or cold air to the Honeywell ScanPal EDA10A. An RAM NFC add-on module can be used to extend the device s internal NFC reader. The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included). Product features RAM Mounts RAM-HOL-HON11PD2-DB9U: Compatible with OEM hand strap Easy insertion and removal Charging function With Latch Prepared for RAM NFC Extender RAM Vent-Temp 2-Hole side mount (Diamond ball base) for additional devices or peripheral accessories Input Connector: 5.5mm DC-Connector Input Voltage: 5V Output Connector: 2x USB-A 2.0 DB9 (Peripheral output - 900mAh per Port) Transferspeed: 12Mbps Input Cable Length: ca. 100 cm Output Cable Length: ca. 25 cm Certifications: RoHS, WEEE, CE FCC Additional information: Devices shown are not included in the delivery. Only the RAM-HOL-HON11PD2-DB9U holder is supplied.

Objav podobné ako RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC