ram mounts tough claw mala svorka s rucnym upinanim pre priemer 15 9 38 1 mm s 1 capom rap b 400u

RAM svorka s ručným upínaním pre priemer 15,9 - 38,1 mm s 1" čapom sa dokonale hodí pre rýchle upnutie vášho zariadenia napríklad na riadidlá motocykla, barany v kokpite lietadla, sedlovku bicykla, madlá na kajaku atď. Bezpečne udrží napríklad mobilný telefón, GPS navigáciu, GPS navigáciu, GPS navigáciu chránia povrch pred poškodením a zaisťujú stabilitu. Čeľuste svorky sú navrhnuté pre guľaté, ploché aj nerovné povrchy. Pre priemer tyče: 0 – 28,9 mm Kompatibilný so systémom ramien a držiakov RAM mount Doživotná záruka RAM mount Materiál: Vysokopevnostný plast Nerez oceľ Veľkosť guľového čapu: Priemer 1\", veľkosť „B", gumový Váha: 159 g Poznámka: „U“ v čísle dielu znamená, že výrobok je balený v PU sáčku.

Objav podobné ako RAM Mounts Tough-Claw malá svorka s ručným upínaním pre priemer 15,9-38,1 mm, s 1" čapom, RAP-B-400U

RAM Mounts Tough-Claw Set - C-Ball (1.5 inches), Tough-Claw Large (Diameter 25.4-55.9 mm), Center Link Arm (approx. 145 mm)

Objav podobné ako RAM Mounts Tough-Claw Set

RAM Mounts Tough-Claw Retaining Clip (Medium) with Locking Screw - C-Ball (1.5"), Diameter 25.4-40.6mm

Objav podobné ako RAM Mounts Tough-Claw Retaining Clip

zárubňa pre stenu 34 až 38 cm
biela zárubňa pre hrúbku steny do 38 cm
WC doska pre rozstup 15,5 cm
kovanie pre vstupné dvere s rozstupom 92 mm
podnož pre stôl DARIO s rozmerom 1800x800 mm
drez pre hornú montáž do skrinky 450 mm
posuvný systém pre dvere šírky 800 až 1250 mm
drez pre skriňu s minimálnou šírkou 500 mm
kovanie pre vstupné dvere s roztečou 72 mm
nádržka pre WC s rozstupom pripojení 180 mm
umývadielko pre malú kúpeľňu 40 cm
priemer sprchovej hlavice 15 cm
priemer odpadu DN 40
rezačka pre dlaždice s hrúbkou do 15 mm
čierna matná sada pre medené rúrky 15 mm
predlžovacia sada pre HANSA skrytú batériu 40 mm

RAM Mounts Tough-Claw Retaining Clip (Small) with Locking Screw - B-Ball (1 inch), Diameter 15.9-29.0 mm

Objav podobné ako RAM Mounts Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Retaining Clip (Small) with Locking Screw - B-Ball (1 inch), Additional C-Ball (1.5 Inch), Diameter 15.9-29.0 mm

Objav podobné ako RAM Mounts Tough-Claw

RAM Mounts Tough-Claw Retaining Clip Base (Small) without Ball - Diameter 15.9-29.0 mm

Objav podobné ako RAM Mounts Tough-Claw

RAM Mounts Tough-Claw Retaining Clip (Small) with Locking Screw - C-Ball (1.5"), Diameter 15.9-29.0mm

Objav podobné ako RAM Mounts Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Retaining Clip (Large) with Locking Screw - C-Ball (1.5"), Diameter 25.4-55.9mm

Objav podobné ako RAM Mounts Tough-Claw Retaining Clip

RAM Mounts Tough-Claw Retaining Clip (Large) with Locking Screw - B-Ball (1 inch), Diameter 25.4-55.9 mm

Objav podobné ako RAM Mounts Tough-Claw Retaining Clip

RAM Mounts Tough-Tray with Flat Side Arms - Universal Laptop Holder, AMPS Mounts

Objav podobné ako RAM Mounts Tough-Tray

RAM Mounts Tough-Tray II - Universal Holder for Laptops / Netbooks / Tablets, AMPS Mounts

Objav podobné ako RAM Mounts Tough-Tray II

RAM Mounts Tough-Dock Cradle for Zebra ET4x 8 Inch Tablets in Zebra Protective Frame - Power Connection 5.5 mm Jack Plug, Dual USB-A, AMPS and VESA Mounts

Objav podobné ako RAM Mounts Tough-Dock Cradle

RAM Mounts Tough-Dock Cradle for Zebra ET4x 10 Inch Tablets in Zebra Protective Frame - Power/Data Connection, 5.5 mm Jack Plug, USB-A, AMPS and VESA Mounts

Objav podobné ako RAM Mounts Tough-Dock Cradle

RAM Mounts Tough-Ball with M8 - 1.25 x 10 mm Threaded Pin - C-Ball (1.5 inches), in a poly bag

Objav podobné ako RAM Mounts Tough-Ball

RAM Mounts Tough-Ball with M10 - 1.5 in. x 25 mm Threaded Pin - B-Ball (1 Inch)

Objav podobné ako RAM Mounts Tough-Ball

RAM Mounts Tough-Ball with M6-1 x 6 mm Threaded Pin - B-Ball (1 Inch), in Poly Bag

Objav podobné ako RAM Mounts Tough-Ball

RAM Mounts Tough-Dock Bracket for Zebra ET4x 10 Inch Tablets in Zebra Protective Frame - lockable, power connection 5.5 mm jack plug, dual USB-A, AMPS and VESA mount

Objav podobné ako RAM Mounts Tough-Dock Bracket

RAM Mounts Tough-Dock Bracket for Zebra ET4x 10 inch tablets in Zebra protective frame - power connection 5.5 mm jack plug, dual USB-A, AMPS and VESA mount

Objav podobné ako RAM Mounts Tough-Dock Bracket

RAM Mounts Tough-Dock Cradle for Zebra ET4x 8 Inch Tablets in Zebra Protective Frame - lockable, power connection 5.5 mm jack plug, dual USB-A, AMPS and VESA mount

Objav podobné ako RAM Mounts Tough-Dock Cradle

RAM Mounts Tough-Dock Cradle for Zebra ET4x 10 Inch Tablets in Zebra Protective Frame - with power supply 5.5 mm jack plug, AMPS and VESA mount

Objav podobné ako RAM Mounts Tough-Dock Cradle

RAM Mounts Tough-Dock Cradle for Zebra ET4x 10 Inch Tablets in Zebra Protective Frame - lockable, power/data connection, 5.5 mm jack plug, USB-A, AMPS and VESA mount

Objav podobné ako RAM Mounts Tough-Dock Cradle

RAM Mounts Tough-Tray - Universal Laptop-Halter, AMPS-Aufnahme

Objav podobné ako RAM Mounts Tough-Tray

Tough-Dock, Active Holder, AMPS, VESA 75x75, fits for: ET4X (8")

Objav podobné ako RAM Mounts Tough-Dock

Štítkový kotúč, Zebra, Materiál: Bežný papier, Z-Perform 1000T, Povrchová úprava: Nie, Lepidlo: Bežné, Šírka: 57.15 mm, Výška: 38.1 mm, Priemer: 200 mm, Priemer jadra: 76 mm, štítkov na rolke: 4270 štítkov, Oddelenie: Medzera, Perforácia: Nie, Farba: Biela, Rec. Stuha: 02300BK08345

Objav podobné ako Zebra 3006097 Z-Perform 1000T, 57,15 x 38,1 mm, 5050 etiket, biele

Štítoková rolka, Zebra, Materiál: Termálny papier, Z-Perform 1000D, Povrchová úprava: Nie, Lepidlo: Normálne, Šírka: 57.15 mm, Výška: 38.1 mm, Priemer: 127 mm, Priemer jadra: 25.4 mm, štítky na rolke: 1720 štítkov, oddelenie: medzera, perforácia: áno, farba: biela

Objav podobné ako Zebra 3007899-T Z-Perform 1000D, 57,15 x 38,1 mm, 1720 etiket, biele

Štítkový kotúč, Zebra, Materiál: Bežný papier, Z-Perform 1000T, Povrchová úprava: Nie, Lepidlo: Bežné, Šírka: 57.15 mm, Výška: 38.1 mm, Priemer: 127 mm, Priemer jadra: 25.4 mm, štítky na rolke: 1790 štítkov, oddelenie: medzera, perforácia: nie, farba: biela, odporúčané. Stuha: 02300GS06407 /02300ZD25707

Objav podobné ako Zebra 880009-038D Z-Perform 1000T, 57,15 x 38,1 mm, 1790 etiket, biele

Štítková rolka, Zebra, Materiál: Bežný papier, Z-Perform 1000T Odnímateľný, Povrchová úprava: Nie, Lepidlo: Odnímateľné, Šírka: 57.15 mm, Výška: 38.1 mm, Priemer: 127 mm, Priemer jadra: 25.4 mm, štítky na rolke: 1740 štítkov, oddelenie: medzera, perforácia: nie, farba: biela, odporúčané. Stuha: 02300GS06407 /02300ZD25707

Objav podobné ako Zebra 3006184 Z-Perform 1000T Removable, 57,15 x 38,1 mm, 1740 etiket, biele

Štítoková rolka, Zebra, Materiál: Termálny papier, Z-Perform 1000D, Povrchová úprava: Nie, Lepidlo: Normálne, Šírka: 57.15 mm, Výška: 38.1 mm, Priemer: 127 mm, Priemer jadra: 25.4 mm, štítky na rolke: 1790 štítkov, ohraničenie: medzera, perforácia: nie, farba: biela

Objav podobné ako Zebra 880177-038D Z-Perform 1000D, 57,15 x 38,1 mm, 1790 etiket, biele

Ochranné sklo tvrdené sklo proti rozbitiu či poškriabaniu ciferníku, vysoká citlivosť dotyku, jednoduchá inštalácia, celolepící vrstva, rozšírená záruka PanzerGlass 24 mesiacov Displej dotykového zariadenia sa kedykoľvek môže aj napriek všetkej pozornosti nepredvídateľne poškriabať, stačí na to iba malá nehoda, ako ho napr. pustiť na zem. Na to, aby ste sa do takejto situácie nedostali, príde vhod ochranné sklo PanzerGlass SmartWatch pre rôzne typy hodiniek (38,5 mm) číre. Jeho vonkajšia povrchová úprava znižuje riziko zanechávania odtlačkov prstov. Vďaka ochrannému sklu PanzerGlass tak bude displej vášho zariadenia stále ako nový. Poskytuje trikrát lepšiu ochranu ako tenká fólia Po aplikácii ochranného skla zostáva totožná citlivosť dotyku PanzerGlass SmartWatch pre rôzne typy hodiniek (38,5 mm) číre sa jednoducho aplikuje

Objav podobné ako PanzerGlass SmartWatch pre rôzne typy hodiniek (38,5 mm) číre (3616)

Táto pravá obložková zárubňa je určená pre dvere so šírkou 90 cm a steny s hrúbkou 34-38 cm. Má biely CPL povrch a skladá sa z viacerých častí. Ide o modulárne riešenie pre jednoduchšiu inštaláciu.

• Pravá obložková zárubňa v bielej farbe pre estetický vzhľad.
• Vhodná pre hrúbku steny 34-38 cm, čo pokrýva bežné rozsahy.
• Povrch CPL zaisťuje odolnosť a jednoduchú údržbu.
• Modulárny dizajn na skladanie uľahčuje prepravu a montáž.

Objav podobné ako Obložková zárubňa Naturel 90 cm pre hrúbku steny 34-38 cm pravá O9CPLBN90P

Ľavá obložková zárubňa z dubu s šírkou 60 cm, určená pre hrúbku steny 34-38 cm. Má CPL povrch a skladá sa z viacerých častí. Je vhodná pre montáž ako obložková zárubňa pre dvere.

• Dizajn z prírodného dubu s odolným CPL povrchom.
• Univerzálna montáž pre hrúbku steny 34-38 cm.
• Modulárna konštrukcia z viacerých častí pre jednoduchú inštaláciu.
• Špecificky určená pre ľavé otváranie dverí.

Objav podobné ako Obložková zárubňa Naturel 60 cm pre hrúbku steny 34-38 cm ľavá O9CPLDN60L

RAP-B-202U kruhový adaptér/úchyt na rovné povrchy s 1\" čapom. Adaptér má priemer 6,35 cm a má predvŕtaných 7 dier, z toho 4 podľa priemyselného vzoru dier AMPS. Použitie: ako adaptér s 1\" čapom pre prepojenie držiakov RAM s ramenami pre 1\" čapy. Najmä sa používa k ťažším univerzálnym držiakom pre veľké tablety. Pre všetky ostatné držiaky sa používa lichobežníkový adaptér RAP-B-238U ako úchyt na rovné povrchy s 1\" čapom. Je určený na pevné nerozoberateľné pripevnenie držiaka na rovnú plochu. Typicky pomocou skrutiek na vhodné miesto palubnej dosky nákladného auta, na palubu lode, board kajaku atď. Prednosti adaptéra: Kompatibilný so systémom ramien a úchytov RAM mount Zodpovedá štandardu AMPS Doživotná záruka RAM mount „, gumový, veľkosti „B“ Poznámka: „„U““ v čísle dielu znamená, že výrobok je balený v PU sáčku.

Objav podobné ako RAM Mounts kruhový adaptér/úchyt na rovné povrchy s AMPS vzorom dier, s čapom 1", plast, RAP-B-202U

RAM Mounts držiak VESA 75x75 mm, s 1,5" guľovým čapom, RAM-2461U EAN: 793442024610 Prehľad Držiak VESA 75x75 mm s 1,5" guľovým čapom. Štvorcová doštička držiaka s rozmermi 92x92 mm. Čap umiestnený 22 mm od stredu hrany. Použitie VESA 75x75 držiak pre LCD monitory, priemyselné PC, terminály atď. Úchyt na rovnú plochu so širokou podstavou pre rad "C" ramien a držiakov RAM s 1,5" čapy. Prednosti Kompatibilný so systémom ramien a úchytov RAM mount radu "C". Zodpovedá štandardu VESA 75x75. Dokonalé spracovanie. Doživotná záruka RAM mount. Špecifikácia Materiál: Povlakovaná zliatina hliníka Váha: 182 g Veľkosť guľového čapu: 1,5", gumový, veľkosti "C" Poznámka: "U" v čísle dielu znamená, že výrobok je balený v PU sáčku.

Objav podobné ako RAM Mounts držiak VESA 75x75 mm, s 1,5" guľovým čapom, RAM-2461U

RAM Mounts Kruhový Adaptér s AMPS Vzorom Dier s Guľovým Čapom 1,5" EAN produktu: 793442001239 Popis produktu Adaptér RAM-202U je univerzálne riešenie pre pevné pripevnenie držiakov na rovné plochy. S priemerom 6,35 cm a 1,5" guľovým čapom je ideálny pre inštaláciu na palube lode, boardu kajaku alebo palubnej doske nákladného auta. Použitie Adaptér je určený pre prepojenie držiakov RAM s ramenami pre 1,5" čapy. Je ideálny pre ťažšie univerzálne držiaky pre veľké tablety. Vlastnosti Kompatibilita: Kompatibilný so systémom ramien a úchytov RAM mount Štandard: Zodpovedá štandardu AMPS Záruka: Doživotná záruka od výrobcu RAM mount Materiál: Povlakovaná zliatina hliníka Veľkosť guľového čapu: 1,5", gumový, veľkosti "C" Váha: 68 g

Objav podobné ako RAM Mounts kruhový adaptér s AMPS vzorom dier s guľovým čapom 1,5", RAM-202U

RAM Mounts X-Grip univerzálny držiak na mobilný telefón EAN: 793442932298 Popis produktu RAM Mounts X-Grip je univerzálny držiak na mobilný telefón s 1" guľovým čapom. Skladá sa z pružinového mechanizmu, ktorý bezpečne udrží váš telefón. Držiak je doplnený zaisťovacou gumou pre maximálne bezpečie vášho zariadenia. Špecifikácia Šírka telefónu: 48 – 83 mm Hrúbka telefónu: do 22 mm Materiál: Nerez oceľ, povlakovaná zliatina hliníka, vysokopevnostný plast Váha: 100 g Veľkosť guľového čapu: 1", gumový, veľkosti „B“ Výhody produktu Držiak X-Grip ponúka bezpečné uchopenie telefónu aj pri vibráciách. Je univerzálny a kompatibilný so systémom ramien a úchytov RAM mount. Ponúka rýchle a jednoduché upevnenie aj vybratie telefónu. Je nehrdzavejúci a dodáva sa s doživotnou zárukou RAM mount. Upozornenie: X-Grip je súčasťou trojdielneho riešenia. Na zostavenie celého riešenia potrebujete okrem tohto držiaka ešte rameno a úchyt.

Objav podobné ako RAM Mounts X-Grip univerzálny držiak na mobilný telefón s 1" guľovým čapom

RAM Mounts Prísavka s 1" čapom Priemer: 70 mm Váha: 91 g Veľkosť guľového čapu: Priemer 1", veľkosť "B", gumový Použitie a montáž Úchyt na sklo a akékoľvek rovné, hladké a neporézne plochy. Vhodný pre malú elektroniku - mobilné telefóny, GPS navigácie, iPhone, iPod, GoPro kamery atď. aj v náročnom vibrujúcom prostredí. Jednoduchá a rýchla montáž pomocou zámku. Materiál Vysokopevnostný plast a guma Upozornenie "U" v čísle dielu znamená, že výrobok je balený v PU sáčku. Ďalšie informácie Na upevnenie držiaka s prísavkou na akýkoľvek iný povrch ako sklo, napríklad na palubnú dosku, použite samolepiacu podložku.

Objav podobné ako RAM Mounts vysoko kvalitná prísavka s priemerom 70 mm s 1" čapom

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CP-NFCU: Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CP-NFCU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCK-SAM62CP-NFCU: Easy insertion and removal Charging function With Latch Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Including RAM NFC-Extender Additional information: This product is not compatible with the GDS Hand-Stand. This holder will not support any NFC functionality of the Tab Active2 Potential interference of NFC functionality may occur when positioned close to strong magnets. Devices shown are not included in the delivery. Only the RAM-GDS-DOCK-SAM62CP-NFCU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM76CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM76CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the "No Battery Mode" function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM78CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM78CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Protective Sleeve - USB-C Power

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+- in IntelliSkin Next Gen Protective Sleeve - USB-C Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Prepared for GDS-FAN 12-VDC axial fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM80CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM80CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A8 10.5" (SM-X200) in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM83CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM83CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A8 (10.5“) in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A8 10.5" (SM-X200) in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM83CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM83CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM88CD2U: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: 2x USB-A (Peripheral output - 900mAh per Port) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm · Prepared for GDS 12-VDC Axial cooling fan Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM88CD2U holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Protective Sleeve - USB-C & Dual USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM88CDU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Output Connector: USB-A (Peripheral output - 500mAh) Input Cable Length: ca. 21 cm Output Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM88CDU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. Data synchronization via the connection is also supported. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM62CU: Compatible with GDS hand-stand Easy insertion and removal Charging function Data synchronization Lockable with key Input Connector: USB-C 3.1 Power Output: 60W Output Voltage: 5-20V @ 3A Input Cable Length: ca. 21 cm Additional information: This product will not support the "No Battery Mode" function. Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM62CU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active2, Active3 & Active5 - in IntelliSkin Protective Sleeve - USB-C Power Supply

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin Next Gen protective sleeve. The holder is powered by a USB-C connection and charges the device in the dock. To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. The cut-outs on the buttons and ports allow you to continue using them without any problems. The back of the device holder is prepared to support a round ball base (not included). Product features RAM Mounts RAM-GDS-DOCKL-SAM76CPU: Compatible with GDS hand-stand Easy insertion and removal Charging function Lockable with key Input Connector: USB-C Power Output: 15W Output Voltage: 5-12V @ 3A Input Cable Length: ca. 21 cm Additional information: Devices shown are not included in the delivery. Only the RAM-GDS-DOCKL-SAM76CPU holder is supplied.

Objav podobné ako RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply